GN developed a new Oilfield Drilling mud centrifuge LWF600x1000N, since more and more clients inquiry relatively larger centrifuge for oilfield drilling to meet various requirement.

LWF600x1000N decanter centrifuge specification

Max treating capacity: 300gpm

Oilfield Drilling mud centrifuge

Normal treating capacity: 264gpm

Average bowl speed: 1800rpm

Bowl diameter: 23.6”

Bowl length: 39.4”

Total power: 52.5KW

Matched pump power: 5.5KW

Previous model decanter centrifuge LWF450x1000N

Max treating capacity: 264gpm

Normal treating capacity: 220gpm

Average bowl speed: 1800rpm

Bowl diameter: 17.7”

Bowl length: 39.4”

Total power: 37.5KW

Matched pump power: 5.5KW

 Compare with LW450x1000N, LW600x1000N has larger treating capacity and larger bowl, which can process more drilling fluids in one time and less drilling cost relatively. They are both middle speed decanter centrifuge, which can separate drilling fluids solids particles 5~7 μm, for some clients, it is enough for drilling fluids cleaning, but for some other clients, they need a high speed centrifuge to separate more fine solids from the drilling fluids, we will recommend GLW355x1250N or GLW-V-355X1250N. The max treating capacity is 176gpm.

 Sometimes you will encounter troubles when operate the centrifuge in oilfield, we would like to offer some suggestions for normal problems, anyway, we will have a engineer to service if complex trouble.

 1 Intense Vibration

 A Solids in the drum doesn’t clear away after last operation

  Solution: Start-up auxiliary motor to flush it by clean water and always remember to clean the bowl after using everytime

Continue reading →

GN designed some new models shale shaker in 2011, all of them are BEM shaker with 3 screen panel, the shaker screen dimension is larger than Derrick FLC 500 & 2000 series shaker, even 3 panel screen area is larger than Derrick 4 panel screen area.

The new designed shale shaker is according to API standard of design procedure,GNPS70-3,GNPS85-3 all matched standard oilfield solids control mud tank.

shale shaker

API standard design procedure of shale shaker

1 Shale shakers skids shall be level.

2 Shakers shall be rigged with adequate space, walkways and handrails to permit easy and safe servicing.

3 if the shaker is equipped with a rear tank, the flow line shall enter the rear tank as near the bottom as possible.

4 A means of diverting fluid from the flow line is recommended to permit the disposal of cement, spotting fluids, contaminated fluids, etc, before these fluids reach the shale shaker. The procedure shall not be used to dump the rear tank into the sand trap before trips.

operation procedure of shale shaker

1 The screens shall be inspected every time circulation is interrupted.

2 Use the shaker screens with the smallest openings that do not cause excessive drilling fluid loss.

3 Under normal operating conditions and when using a single-deck shaker with multiple screens, all screens shall have the same API designation.

4 Torn or damaged screens shall be replaced or repaired promptly.

e.g.GNZS63-3 shale shaker use wedge technology, it is easy to change and install Brandt Cobra shaker screen.

GNZS83-3 shale shaker use tension bolts to install screens.

5 When using shaker screens that need tensioning, tension shall be checked 15 min to 30 min after installation and tourly thereafter.

Continue reading →

GN solids control specialises in the supply of solids control equipments based systems and associated solids control services, applicable to a broad spectrum of solids control and separation applications on a worldwide basis.

New and ever increasing environmental legislation increases the importance of employing efficient and reliable methods to meet waste reduction and minimisation targets.

solids control service

Related service of Solid control

What is the content of Solids control service?

Solids control service in Indonesia 

1 Pt. Saribumi Prima Utama :

Continue reading →

GN solids control designed and manufactured slurry separation system for TBM project. GN250, GN400, GN600 is special for TBM project in Hongkong.

What is TBM?

TBM slurry separation system

A tunnel boring machine (TBM) also known as a “mole”, is a machine used to excavate tunnels with a circular cross section through a variety of soil and rock strata. They can bore through hard rock, sand, and almost anything in between. Tunnel diameters can range from a metre (done with micro-TBMs) to almost 16 metres to date. Tunnels of less than a metre or so in diameter are typically done using trenchless construction methods or horizontal directional drilling rather than TBMs.

Function of TBM

Tunnel boring machines are used as an alternative to drilling and blasting (D&B) methods in rock and conventional ‘hand mining’ in soil. TBMs have the advantages of limiting the disturbance to the surrounding ground and producing a smooth tunnel wall. This significantly reduces the cost of lining the tunnel, and makes them suitable to use in heavily urbanized areas. The major disadvantage is the upfront cost. TBMs are expensive to construct, and can be difficult to transport. However, as modern tunnels become longer, the cost of tunnel boring machines versus drill and blast is actually less—this is because tunnelling with TBMs is much more efficient and results in a shorter project.

GN400 slurry separation system is composed of the following items:

1 GNZS83-3 shale shaker 2sets , with 2.7m3 pyramid screen area and max 7.0G vibrating strength

The shaker screen is not same as common oil drilling shaker screen, it is a kind of slit type shaker screen, material is stainless steel wire. It can process large solids such as rocks, the function is same as scalper. But if the solids in the mud is not so large, you can change a small mesh screen so that the treatment effect could be better, so it is much flexible than scalper.  

2 GNZJ83-3 desander 1set, use 3 pcs 12” PU hydrocyclones with underflow shaker GNZS83-3

3 GNZJ83-3 desilter 1 set, use 18pcs 5” PU hydrocyclones with underflow shaker GNZS83-3

 5”  Hydrocyclones can process larger capacity than conventional 4” cone, and it is not easy to jam the inlet of desilter. The GNZJ83-3 desilter is designed of round arrangement, the round arrangement is with compact structure and better performance than horizontal line.

Continue reading →

As refer to mud gas separator or poor boy degasser, you may heard of “Flare stack”.

A flare stack (alternatively known as gas flare ) is a vertical vent pipe used in oil and gas drilling sites. The pipe diameter of flare stack is usually 8” for GN ZYQ series poor boy degasser.

flare stack

The function of flare stacks

They are used to eliminate waste gas invaded in the drilling mud, otherwise it will lead to “blowout”, “kick”. They also act as safety systems for non-waste gas and is released via pressure relief valve when needed to ease the strain on equipment. They protect gas processing equipments from being over pressured. Also in case of an emergency situation, the flare system helps burn out the total reserve gas.

How flare stacks work

Whenever the poor boy degasser are over-pressured, the pressure relief valves automatically releases gases which are routed through large piping runs called flare headers to the flare stacks. The released gases are burned as they exit the flare stacks. The size and brightness of the resulting flame depends upon the flammable material’s flow rate in terms of joules per hour.

In order to keep the flare system functional, a small amount of gas is continuously burned, like a pilot light, so that the system is always ready for its primary purpose as an over-pressure safety system. The continuous gas source also helps diluted mixtures achieve complete combustion. Enclosed ground flares are engineered to eliminate smoke, and contain the flame within the stack.

Continue reading →

The mud gas separator is used in a ‘kick’ situation to separate large volumes of free gas invaded in the drilling fluid.

 Function of Mud gas separator

 Mud gas separator also called poor boy degasser, Gus buster, which is designed to provide effective separation of the drilling mud and invaded gas from the well by venting the gas and returning the mud to the mud pits. Small amounts of entrained gas can then be handles by a

liquid gas separator

vacuum-type degasser located in the mud pits. The mud/gas separator controls gas cutting during kick situations, during drilling with significant drilled gas in the mud returns, or when trip gas is circulated up.

 Mud leg height is an important parameter for the mud gas separator, you need to clear it during evaluation.

 What is Mud leg?

The mud leg in the separator is controlled by adjusting the fluid level in the mud tank or by moving the separat6or up or down within the tank. Mud tank height can restrict the maximum mud leg obtainable for open-bottom mud gas separator.

 Mud leg is an important part for mud gas separator, it is also called Fluid level. Fluids level is maintained in a float mud gas separator by a float/valve configuration. The float opens and closed a valve on the mud return line to maintain the mud leg level. Valves can be operated by manual linkage system connected from the float to the valve, or the valve can be air-operated with the rig air. Mud leg height can be controlled by adjusting the float assembly.

 There are some inherent problems in the use of float-type mud gas separators. The manual linkage separator has experienced problems with linkage failure resulting in improper opening or closing of the mud return line valve. Air-operated valves fail to function if rig air is lost, resulting in no control of fluid level within the separator. Mud-return-line valves are prone to plug with solids, preventing mud flow back to the mud pits.

 Gas Flow calculation is another important issue to evaluate the mud gas separator.  

Usually we need to calculate the following items.

Continue reading →

GN produce centrifugal pump for VACUFLO vacuum degasser, usually it is installed on the skid of the mud tank,together with the feeding pump of desander&desilter. The flow rate various from 20m3/h ~400m3/h.

centrifugal pump

Firstly, we should introduceVACUFLO vacuum degasser briefly.

 Function of vacuum degasserAn efficient degasser is essential to safe and productive drilling operations. Gas present in the well bore can reduce the hydrostatic head in the well bore – with the potential for even greater gas influx and possible blow-out.

How do vacuum degasser work?

Vacuum degassers work by creating lower pressure inside a vessel so air or other gaseous impurities can be removed from a substance, such as water or even molten steel. The air is siphoned from the vessel after pressure is lowered enough to force the gas from the substance.

Features of Derrick VACUFLO vacuum degasser

Derrick’s Design

More Leaf Surface Area

Corrugated Fiberglass Leaves

Gas Extraction

Large Access Door

Compared with Derrick VACUFLO vacuum degasser, GN vacuum degasser has the following features.

1 Smaller area required

Because of different design, GN Vacuum dgasser do not a feeding pump, it is a self priming one, so you save a lot of area to install the feeding pump of vacuum degasser.GN vacuum degasser have a compact structure which can be installed on the tank easily.

Continue reading →

Hole Openers are used for expanding the drilled hole，it is a kind of drilling rig tools. There are many good suppliers and manufacturer of hole opener in China, with  good quality and competitive price. Some of the manufacturer produced hole opener according to API standard.

 Function of Hole opener

 1. When drilling of the big hole is not possible because of the rig capacity.

2. When a satisfied penetration rate is not obtained in case of the big hole drilling, it is used after drilling with smaller bit.

3. When the hole direction most be controlled.

 Cutters of Hole opener

Several types of the cutter are

hole opener

 made available for various formations to be drilled, such as soft, medium and medium hard formations. Type SM for soft to medium formation,type MH for medium to hard formation and type XH for hard formation. For soft to medium and abrasive hard formations, the cutters with tungsten carbide tips are also available.

 Fixed Diameter Hole Opener

 Fixed Diameter Hole Opener is used to enlarge a hole or connected with a bit on front end to drill pilot hole and enlarge hole. Fixed Diameter Hole Opener is a general hole enlarging tool and is designed for enlarging holes onshore and offshore in oilfield during drilling. It is made of tough heat treated alloy steel for maximum strength. Cutter arms, equipped with removable cutter, are hardfaced and welded on body. The hole openers have three or six jet tubes with replaceable nozzles,so that jet streams quickly clean the enlarged hole.

 How to inquiry or order the hole opener in China?

You need to advice the following information.

1 Hole size

2 Pilot hole size

3 Top and bottom connections

4 Fishing neck and bottom neck length and OD.

5 Types of cutters (SM, MH, XH)

Hole opener manufacturer in China

1 Lilin Group, loaded in Tianjin city.

LILIN is the largest manufacturer of downhole drilling motor in Asia area. also famous manufacturer of drill bits in china. The company most significant value is our leading edge technolog ies and engineers that continually innovate and create update product to apply our technology to drilling situations.

2 Kingdream Public Limited Company located in Wuhan city

To know more about hole opener manufacturer in China or other drilling rig tools manufactures, pls contact GN solids control.

GN is a China Centrifugal pump top manufacturer,we supply centrifugal pump mainly used for Oil gas  drilling mud solids control system,HDD(Horizontal directional Drilling) mud recycling system.Our centrifugal pump can be used as desander desilter feeding pump,mixing pump,supercharging pump,trip pump.Learn more:China Sand Pump.

China Centrifugal Pump

Both horizontal and vertical type centrifugal pump are available from GN Solids Control.

Following is some recommendations for USA and Japan Centrifugal pump manufacturers.

• NOV Mission Centrifugal Pumps American Manufacturer

The National Oilwell Varco Mission centrifugal pump line has proven to be the best centrifugal design for handling abrasive mud. This pump line offers a broad selection of innovative features for a variety of routine, demanding, abrasive and corrosive applications. These pumps are designed for a wide range of flow rates, from a few gallons per minute to thousands of gallons per minute.

During the 1950’s the Mission® 1780 type “W” pumps were introduced to replace duplex pumps while creating the first low pressure mud system. The use of a high quality, concentric type centrifugal pump allowed abrasive fluids to be mixed and transferred while reducing initial and maintenance costs for the drilling industry. The low-pressure mud system with Mission 1780 Type “W” centrifugal pumps became the industry standard.

As well depths increased, so did the need for heavier mud weights. When the mud weight began exceeding 14 ppg, the need for a pump that could withstand greater horsepower loads arose. During the 1970’s, Mission organized a design

team that engineered the Mission Magnum. The Magnum was designed to have the same footprint, flange locations, and drive shaft diameter as the 1780 “W”. This allowed a 1780 to be replaced by a Magnum without any skid modifications. The Magnums were engineered with a 2 1/2″ shaft (3″ between the bearings), double row bearings with an engineered life of over 2 years at 200 HP, larger impellers and heavier frames. The Magnum allowed drilling contractors to upgrade their centrifugal pumps and mix heavier fluids.

National Oilwell Varco is dedicated to continual improvement of our product line and offering innovative solutions to service our customers for centrifugal pump.

Derrick Centrifugal pump-USA Manufactuer

GN design complete line mud cleaning equipment for Oil&Gas drilling mud solids control,HDD mud recycling system,and indusrial slurry cleaning.

Four phase mud cleaning equipment

• Shale Shaker

Shale Shaker is the first and most important equipment for drilling mud cleaning.This clenaing equipment separate

Mud Cleaning Equipment

particle size usually above 70mirons.
We provide both linear motion shale shaker and balanced elliptical motion shale shaker.

• Desaner/Desilter/Mud Cleaner

Desander with 10inch cones,or 8inch cones,or 12 inch cones act as the second phase drilling mud cleaning equipment.We have customized number cones desander for clients.Desander cleaning mud usually between 47-76microns.Desilter with 4inch cones,or 5inch cones,act as the third phase mud cleaning equipment.Which clean out particles 15-45microns.Mud cleaner is a combination of desander & desilter and with underfluids bottom shale shaker,which act as both desander and desilter function.Mud cleaner manimum footprint of the equipments,and has big capacity for mud cleaning and treatment. Continue reading →