Shear pump is usually used together with Jet mud mixing unit, to be assembled as a jet shearing unit in oilfield solids control system.

Jet shearing unit

The jet shearing unit is formed by shear pump, mixing hopper, pipeline and polymer/clay hydrator. For installation transportation, the polymer/clay hydrator is formed by a separate compartment.

oilfield shear pump

The pump should be located the liquid source so that the suction line can be short and reduce loses. The foundation should be sufficiently rigid and substantial to absorb any vibration and support the base plate at all points. The base plate should be installed in a level position.

Oilfield shear pump

The JQB series shear pump adopts a set of compound seal for no leakage at stuffing box. Inside pump is a 300series stainless steel turbine containing 44 nozzles, four scoops and shear plate. Fifty(50)% of the fluid is sheared twice each time through the pump. This turbine shear pump is mounted on a special base with belts and sheaves to drive pump, OSHA type belt guard and a electric motor. Included is a special hopper(ZHP150) with nozzle sized for this application and one mud kit as a package in order to build a complete shear and hydration system. The pump is designed to give longer service life through the improved shaft seal.

There are many principles of proper pump installation and application as well as special considerations for the pump design which, if followed, will further enhance the performance of your shear pump.

This document will deal with both general and specific recommendations for improved JQB series turbine shear performance in both oilfield and industrial applications.

Continue reading →

GN solids control is specialist of oil and gas drilling mud solids control in China. Since 2010 we started to attend important oil & gas exhibition in the world according to our major market.

GN main equipments:

Shale Shaker, Mud Cleaner , Desander ,Desilter, Centrifuge, Agitator,Degasser,Mixing Hoppers, Flare Igniter, Various Tanks, Pumps, Shaker Screens ,Mud Gun

shale shaker for Argentina oil show

GN major application :

1 land rig oil & gas drilling

2 offshore drilling waste management

3 trenchless drilling

Here is a list of world’s top 3 oil & gas exhibition collected by GN solids control.

1 OTC

Founded in 1969, the Offshore Technology Conference is the world’s foremost event for the development of offshore resources in the fields of drilling, exploration, production, and environmental protection. OTC is held annually at Reliant Center in Houston.

Each year, OTC attracts more than 65,000 attendees and 2,000 exhibiting companies representing more than 110 countries.

OTC is sponsored by 12 industry organizations and societies, who work cooperatively to develop the technical program. OTC also has endorsing and supporting organizations.

GN will take a complete mud recycling system there , we have a 108m2 booth for our system and equipments. Welcome to visit us in 2012.

2 SAOGE

SAOGE continues to be the largest oil & gas industry exhibition, ever staged in Saudi Arabia, offering clients unique access to the regions oil and gas sector.  

3 CIPPE

  Continue reading →

World’s top 5 trenchless drilling rig manufacturers list collected by GN solids control.

As a trenchless drilling mud system manufacturer, GN has designed and manufactured many sets of complete mud cleaning/recycling system for trenchless drilling rigs, mainly used for horizontal directional drilling. Here we collect World’s top 5 trenchless drilling rig manufacturers list.

trenchless drilling Mud System

1 Vermeer (http://www2.vermeer.com/vermeer/AP/en/N/ )

2 Ditch Witch (http://www.ditchwitch.com/trenchless/directional-drills/ )

3 American Auger(http://www.americanaugers.com/ )

4 Astec Underground(http://www.astecunderground.com/)

5 Herrenknecht (http://www.herrenknecht.com/)

Vermeer and Ditch Witch are well known brand in the world.

1 Vermeer rig

There’s a lot to consider when purchasing or leasing a horizontal directional drill — features, durability, support, training and overall value. But one area often overlooked is the potential resale value of the unit.
Too often contractors will overlook the potential value of the machine after its useful life in their operation is over. In addition, as more contractors utilize leasing as an acquisition strategy, resale value becomes a more important component in the purchase decision.

Vermeer has distributor everywhere in the world, you can get good after-sales service from them easily.

To see GN solids control equipments for Vermeer trenchless rigs here:

Shale shaker, desander, desilter, decanter centrifuge, mud tank

2 Ditch Witch

Continue reading →

GN solids control choose Italy Oli brand vibrating motor for all our shale shakers. Vibration motor is important components for shale shaker, I will introduce briefly about vibrating motor installation & maintenance.

1 How to install vibrating motor ?

shale shaker vibrator

 (1). Before installing vibrator, turn off and lock out/tag out all energy sources to mounting structure according to ANSI standards。

(2). If using a cutting torch or welding, test atmosphere for gas level or dust content.

(3). Make sure mounting surface is strong and flat, 0.25 mm acros vibrator feet. (This will minimize internal stress to vibrator casting when tightening mount bolts.

(4) Make sure mounting surface and vibrator are clean and free of debris, paint, and oxidation.

(5) Before installing vibrator onto mount, apply thread sealing compound to all bolts.

(6) After the vibrator has been operated for 10 to 20 minutes, check bolt torque. Tighten if necessary

2 How to  maintain  vibrating motor?

(1)Clean dust on shell regularly

(2)Before operating, must check the bolts to confirm whether there is loose or not. Otherwise, we must screw bolts tight before running shaker

(3) Inspect the cable, whether there is wear, hold down, crushing, etc.

(4) the vibration motor should be under good lubrication during operation:

Motors before fixed on shaker, the bearing is filled with SKF specific lubricate grease, the temperature range is -40 ~ 200℃

During running, every 2000 working hours user should makeup LGHP2 lubricate grease once. Every bearing can not be filled over 25.8g.

Continue reading →

GNZS703 shale shaker is widely used for oil and gas drilling and directional drilling in the world.

1 shaker deck adjustment

A spring-loaded plunger and reversible pawl provide a ratcheting action during movement of the operating handle. A full 180 degrees of movement is possible in both directions. Depending on pawl setting, moving the handle in one direction turns the jack screw to raise or lower the screen frame, while in the other direction the jack screw remains stationary during handle movement. The spring-loaded pawl permits the operator to switch the direction to either raise or lower the screen frame, as required.The angle of the discharge end of the screen frame is infinitely adjustable within the equipment’s available range.

2 shale shaker maintenance

(1)Inspect discharge duct connection on side of hopper for leaks. Tighten connection and/or add silicone sealant to prevent leakage.

(2)Inspect cover on unused hopper discharge connection for leaks. Tighten connection and/or add silicone sealant to prevent leakage.

(3)Using a water hose, wash off accumulated process material from screen frame, interior of hopper and AWD angle adjustment components.

(4)Excess process material in these areas may impede angle adjustment of screen frame and can reduce screen frame vibration if the frame bottoms out on the buildup.

(5)Check for and remove any accumulation of process material or other obstruction in feeder interior. Feeder blockage may cause excessive splashing and uneven distribution of slurry onto the screen bed.

Continue reading →

Gas buster also called poor boy degasser or mud gas separator, which is used for oil and gas drilling. The description on oilfield glossary is “A simple separator vessel used to remove free or entrained gas from fluids circulated in the wellbore, such as mud used during drilling operations. The gas buster typically comprises a vessel containing a series of baffles with a liquid exit on the bottom and a gas-vent line at the top of the vessel”.

GN solids control is seeking for a reliable and powerful partner who makes mud tanks in Latin America, we will provide solids control equipments and when tank is ready, you can install it on the tank.

agitator mixer

Because of the long distance shipment from China to Latin America, and the high import tax of mud tank, the economic way is to make the tank by local mud tank manufacture and installed with GN equipments. We will have a technician for instruction of installation.

Agitator mixer uses an impeller to mix and suspend the solids using both axial and radial flows, and by utilizing low shear mixers to suspend and mix mud additives particle size degradation and polymer shear. Unlike centrifugal pumps or mud guns. The Mud Agitator is relatively low shear and low energy device, so it’s easy to operate and inexpensive to maintain. This will ensure that mud additives are homogeneously mixed to prevent dead spots. Agitators will keep the active mud system flowing even when the pumps are disengaged and keep the weighting agents in suspension.

BENEFITS OF AGITATOR MIXER:
     – Increase performance of solids removal equipment.
     – Maintain a uniform mud density.
     – Prevents solids settling , taking up valuable tank displacement.
     – High shear mixing, aids chemical and solids addition.

FEATURES OF AGITATOR MIXER:
     – Compact design.
     – Quiet, smooth, vibration free.
     – Durable, single reduction worm gear drive.
    Continue reading →

GN solids control is specialist of solids control equipments for rotary rig in China, we have various kinds of mud equipments in stock, welcome to inquiry us.

Rotary rigs drill the vast majority of wells today, including all medium and deep wells. The rotary rig consists of four major systems. These include the engines, and the hoisting, rotating, and mud systems.

rotary rig equipments

General of drilling mud(drilling fluids)

Common drilling mud is made of bentonite clay. A heavier drilling mud can be made by adding barite. Various chemicals are also used in different situations. The drilling mud liquid is usually water but is sometimes oil-based. Drilling mud are described by weight. Water weighs 8.3 pounds per gallon. Average bentonite drilling mud weighs from 9 to 10 ppg. Heavy drilling mud weighs from 15 to 20 pounds per gallon. The heavier the drilling mud, the greater the pressure it exerts on the bottom of the well.

Fluid is circulated while the drilling proceeds. Powerful pumps move the fluid down to the pipe, through the bit and back to the surface, carrying the cuttings and other debris with it. Thus, on a rotary rig , drilling can be continuous as stopping to bail the cuttings is no longer required.  The drilling mud also stabilizes the walls of the hole.

Mud circulation system for rotary rig

Drilling mud is stored in steel mud pits beside the rig. The drilling mud then flows down through the hollow rotating drill string and jets out through holes in the drilling bit on the bottom of the well. The drilling mud picks cuttings from the bottom of the well. It flows up the well in the space between the rotating drill string and well walls.

Continue reading →

Last month GN shipped 2 sets of 800gpm mud cleaner to a China Government Company for HDD project. They checked our complete mud system taken to CIPPE, and would like to request 2 sets similar one with small changes.

Now we have standard HDD mud system( mud cleaner) with standard equipments and specs for  150gpm, 350gpm, 500gpm, 800gpm, 1000gpm. Clients can make smaller changes according to his separate requirement.

800gpm mud cleaner for HDD

To make some changes, such system can be used for water well drilling, coal bed methane, geothermal well drilling, diamond drilling, core drilling etc projects. So sometimes clients ask us to make a system with 2 functions( can be used for 2 different projects, and can meet the flow rate requirement for each project). So they can save cost for another set mud cleaner.

How to design the mud tank for the mud cleaner?

１　confirm type of the mud tank, trailer mounted, skid mounted or Hydraulic lift type.

2   confirm the dimension of the mud tank

  You need to consider 3aspects, 1 required storage capacity  2 transportation limit in Client’s country 3 international shipments limit, by container, by bulk cargo or by flat rack container.

3 confirm the qty of the mud tank(according to required mud storage capacity and equipments required place)

4 how many compartments for each tank( according to equipments and function of each compartment)

5 layout of the equipments on the tank

Continue reading →

GN solids control will attend Argentina Oil & Gas Expo 2011 in Otc. We just came back from Brazil Offshore 2011 last month with big success.We will attend the show with our exclusive agent in Argentina together, welcome to contact us by English, Portuguese, Spanish, Chinese languages.We have experienced Technician and Sales there to be ready to service for you.

GNZS703 shale shaker

General info. about

AOG 2011

• Show Name: Argentina Oil & Gas Expo 2011
• Show Time: 10^th to 13^th Otc 2011,14:00~21:00 p.m.
• Venue: La Rural, Buenos Aires, Argentina
• GN Booth number：Q12
• GN Booth Area: 38m2
• What GN show? GLW355X1250N high speed decanter centrifuge and GNZS70-3 linear motion shale shaker, etc, welcome to check our equipments during the show.

GN equipments and system can be used for the following projects:

1 HDD mud system

2 onshore drilling solids control system( oil & gas drilling, water well drilling, coal-bed methane drilling, geothermal well drilling,etc)

3 drilling waste management

4 liquid mud plant ( to prepare for clean mud)

high speed decanter centrifuge

What will be exhibited in the show?