This week, GN Solids Control completed a batch of drilling fluid shaker orders for Russian customers. All shakers are assembled and tested and will be shipped later.

The drilling fluid shaker device has always been used as the first stage separation equipment in solid systems. GN Solids Control vibrating screen has been used in domestic and international drilling sites, and has been well received. The following characteristics of GN Solids Control drilling fluid shaker make it widely praised.

1. GN Solids Control drilling fluid shaker has a simple structure. Every part of the shaker can be easily identified and assembled, making it easy to operate the shaker.

2. In order to ensure the processing capacity, the deck of the GN Solids Control vibrating screen is heat treated and can withstand the high vibration force. Depending on the operator, the shaker table angle can be adjusted during machine operation. By adjusting the panel to a negative angle, you can increase the flow. By adjusting the cover plate to a positive angle, the liquid accumulated on the screen can be increased, and the discharged solids can be dried. The shaker deck is also equipped with locking devices for security purposes.

3. GN Solids Control shale shaker usually use vibrators with international brands. According to customer requirements, GN Solids Control can also be equipped with shakers of other brands on the shaker.

4. The GN Solids Control shaker is equipped with a composite frame shaker screen made by GN Solids Control, which can obtain better separation performance. Composite screens have a longer life.

More question,welcome contact GN Solids Control

In the GN Solids Control assembly shop, a set of drill cuttings solidification equipment is ready for shipment to the GN Solids Control customer site. Cuttings solidification equipment is the most ideal equipment for water-based cuttings processing. GN Solids Control This device has been upgraded several times since its first release in 2014. The better design and easier installation make this device more and more popular with customers.

How GN Solids Control drill solidification equipment works

GN Solids Control curing equipment is mainly used as the final stage processing equipment in drilling and cutting management system. It collects the waste debris discharged from the mud recovery equipment and mixes it with coagulant and desiccant to make the waste debris into water-insoluble compounds so that toxic chemicals and heavy metal ions will not penetrate into the soil and underground. Water mixed.

Optimized Design of GN Solids Control Drill Cuttings Solidification Equipment

1. GN Solids Control changed the design of one skid and divided the whole device into two skids. This gives users the flexibility to position the system on site and each skid will be easier to transport. The two slide rails are connected using steel bars to maintain the distance and stability of the entire system.

2. The curing agent and desiccant are stored in the separation tank, which is easy to operate and can be accurately added to the mixing cabinet. The cabinet has a liquid inlet that can be connected to a hose for other types of chemical injection.

3. In order to ensure uniform stirring, water spray pipes and nozzles are also installed on the mixing cabinet to prevent the materials from being too dry to stir. The spray hose can also be used for flushing after use.

4. The mixing cabinet has observation and maintenance openings from which the operator can perform maintenance. A limit switch is installed on the cover of the observation port to prevent the machine from running without closing the cover.

GN Solids Control drill cuttings curing equipment can be used to treat drill cuttings from primary drilling fluid shale shakers, cyclones and decanters. For more information, feel free to contact GN Solids Control.

Recently, GN Solids Control has undertaken the development and production of a Oil sludge treatment system for a domestic oilfield unit. The project mainly deals with oily solid wastes in sludge storage tanks. After the oily solid wastes have been prepared, sieved, cleaned, demulsified, and finely screened, they have now achieved reductions and preliminary separation. The oil-containing sludge three-phase separation system uses a combined process of a two-phase horizontal spiral centrifuge and a three-phase disc centrifuge to perform final solid-liquid-liquid three-phase separation of subsequent materials to realize the harmless separation and disposal of resources.

System process description:

After the sludge is metered at the inlet, it is pumped to the decanter centrifuge by a booster pump. At the same time, the chemical dosing system injects flocculant into the decanter centrifuge to promote the solid-liquid two-phase separation of the decanter centrifuge. The separated solid phase is transported externally via a screw conveyor. At this time, the liquid content of the solid is <85%, and the solid content of the separated liquid phase is <3%. The solid phase flows to the waste liquid buffer tank through a closed pipe, and the waste liquid buffer tank. Equipped with a liquid level transmitter, the liquid level signal can be displayed locally and remotely. The solid phase settled at the bottom of the waste buffer tank can be returned to the decanter centrifuge for reprocessing through the inlet booster pump.

The process is as follows:

The liquid phase outlet of the waste liquid buffer tank is pumped to the disc centrifuge inlet through a 3um solid particle filter (protecting the downstream disc centrifuge), and the solid, oil and water are separated by centrifugation, and the separated solid phase is stored. Into a solid waste storage tank that can be transported; the water content of the separated oil phase is less than 10%, and temporarily stored in the sewage oil buffer tank; the solid content of the separated water phase is less than 1%, and temporarily stored in the sewage buffer tank The oil and water phases are metered out by centrifugal pumps. Sewage buffer tanks and slop oil buffer tanks are equipped with liquid level transmitters, which can display liquid level signals locally and remotely; the two centrifuges need to achieve structural sealing, and have start-stop, variable frequency, speed, bearing temperature signal feedback and Status information feedback functions such as alarm, centrifuge material overload current signal feedback and alarm, with nitrogen protection and independent flushing water circuit.

More question,welcome contact GN Solids Control

Recently, a set of 200 cubic mud purification system ordered by Australian oil service company customers has been adjusted and received. As the customer’s drilling site is in the virgin forest and there is no road for truck transportation, this system will be chartered directly across the ocean to warm Australian drilling site across the ocean.

This system is equipped with 6 mud tanks, 2 shale shaker, 1 cleaner, 1 liquid-gas separator, 8 centrifugal pumps, 2 jet mixing devices and 18 agitators. The standard container design covers an area Small area and convenient transportation. As mentioned above, in order to facilitate helicopter lifting and transportation, the mud tank and tank surface equipment of this system adopt a streamlined, integrated design, and the total weight of each lifting unit is strictly controlled to not exceed 9 tons. Considering the ease of lifting and the ease of installation, each integrated unit only needs to be placed on the site in sequence and the relative position determined according to the positioning link, and the manifold and power can be connected to start operation.

“What customers are anxious about! What customers want!” Is the service tenet of GN solids control. It is precisely this service tenet that all the company ’s general managers to workshop employees pay close attention to customer needs and strictly control product quality. The company’s more than ten years of ups and downs since its establishment in 2007 have made the “GN solids control” brand trusted by customers at home and abroad. In the future, GN solids control will take ten, twenty, fifty, or even a hundred years. To realize the vision of GN solids control: to operate a well-respected solid control equipment brand.

If you want more information, please contact us

In November 2019, GN Separation was divided into two routes. In addition to participating in the 2019 Indian IFAT environmental protection exhibition in India, another colleague brought separation conveying equipment (including a decanter centrifuge and a solid vacuum pump) to participate in the 2019 Italian Green Technology Environmental Protection Exhibition. GN Separation Separation and Conveyance Equipment Co., Ltd. is a subsidiary of GN Solids Control. It continues to focus on the development and manufacture of separation and conveying equipment for the environmental protection industry.

On November 5-8, 2019, GN Separation placed the GN “Star Product”-GNLW224EP-VFD Series Horizontal Screw Centrifuge-GNSP-10B Solid Vacuum Pump during the Green Technology and Environmental Protection Exhibition in Italy 2019 GN Separation integrates R & D, design, manufacturing, sales and service. Its products serve more than 60 countries and regions in the world. It has formed a well-known domestic and foreign high-end distribution brand, GN Separation. 70% of the company’s products are exported to the international market and have been sold to more than 60 countries and regions in the world, including the United States, Australia, the Middle East, Russia, Europe, Southeast Asia and other regions.

GMLW224EP centrifuge is one of the smallest industrial centrifuges in the world. It can be used as a test widely dispersed drilling mud treatment, sewage environmental protection treatment, oily sludge treatment, chemical and food and beverage industry solid-liquid separation. GNLW224EP-VFD series decanter centrifuge is designed for a single processing capacity of 5m3 / h, and its design maximum variable is 5000RPM. Adopting frequency conversion control, the conventional conversion is adjustable between 0-4500RPM. The maximum separation factor is 3077G, and the diameter of the separated particles is 2-5 μm. GNSP-10B solid vacuum pump is a high-definition and strong suction vacuum conveying pump, also called solid conveying pump or drill cuttings conveying pump. Its unique structure design enables it to work in the most difficult environments, with low maintenance rate and high speed. Conveying more than 80% of solid phase materials and high specific gravity materials. The high-efficiency Venturi device can generate up to 10 meters of water column vacuum to transport materials under strong air flow, with almost no wear parts. The pump body has a compact structure and is suitable for conveying high-density materials. Commonly used for drilling cuttings and oily sludge.

If you want more information, please contact us

Recently, GN Solids Control completed the design and manufacture of a sludge treatment unit for an oilfield environmental protection unit. Since the sludge treatment system was put on the market, it has received extensive attention from customers in the industry, and the feedback from the market on-site operation is good. More and more oilfield environmental protection business contractors use this system as an important solution to efficiently and economically reduce the content of harmful substances in sludge.

The oil sludge treatment system has two separation principles of chemical action and physical separation procedure, and consists of several modules with different functions to gradually recover the water and oil in the sludge. Here is an introduction to the system:

Sludge vacuum extraction module——The sludge from oil-based mud drilling cuttings has high viscosity and large sludge content, and requires a powerful and efficient conveying device to send sludge from the sludge pit to the sludge treatment system. GN Solids Control Sludge Vacuum Pump is a full pneumatic conveying pump without electrical components. It does not generate any sparks during use, and is especially suitable for oil and gas explosion-proof environments. The vacuum degree of 85Kpa can suck and discharge viscous sludge sludge to a long distance.

Pre-mixing module—Before the sludge is sent to the separation module, the material needs to be homogeneously mixed to a liquid content of more than 80%. At the same time, in order to enhance the separation effect of oil and mud, chemical agents need to be added during the homogeneous mixing process.

Separation module-GN Solids Control uses different separation equipment to separate oil and water from the sludge step by step. This design guarantees the continuity of the construction process, and the load of each step process is accurately calculated to avoid bottleneck processes. Shale shaker are used for two-phase separation of coarse solids and liquids. The centrifuge can remove most of the fine solids in the wastewater discharged by the shale shaker, so that the three-phase disc separator will not be overloaded when separating oil, water and ultra-fine solids. GN Solids Control innovatively arranges the swash plate sedimentation device between the centrifuge and the three-phase disc player to ensure that the three-phase disc machine works normally without blocking.

This set of sludge treatment system is very complete in configuration, covering almost all sludge separation equipment, and has very complete functions. Under the premise of ensuring complete functions, GN Solids Control has accurately designed the sludge system, so that all equipment is installed on 3 skids, which has the characteristics of compact structure and convenient transportation. More question welcome contact GN solids control

Non-excavation construction is a horizontal drilling project applied to construction or infrastructure projects. During non-excavation construction, drilling mud needs to be used to ensure the performance of the non-excavation rig. To make drilling mud reusable and reduce drilling costs, contractors often use mud recovery systems to recover drilling mud.

GN Solids Control has more than ten years of experience in the design and manufacture of mud recovery systems. Especially in non-excavation projects, it has multiple bell compact mud systems available for customers to choose from. According to the different requirements of users and the site area limitation, GN Solids Control can provide different configurations of mud recovery devices to meet the requirements of different working conditions. There are usually two types of mud purification systems suitable for non-excavation construction: one is a sand removal cyclone purification system, and the other is a self-contained mud recovery system.

The desander system has a small footprint and is economical. The system consists of a cyclone and a shaker, both of which are mounted on a small collection tank. The sand removal cyclone purification system is a two-stage separation device whose function is to remove coarse particles from drilling mud. The sand removal cyclone purification system is mainly used in projects that can accept large-diameter solid drilling mud, such as piling projects.

GN Solids Control’s self-developed high-grade mud recovery system can be divided into four stages: coarse rock cuttings, sand, mud, and ultra-fine solids. The mud tank of the high-equipped mud recovery system is larger and has enough space to store the purified drilling mud. At the same time, it has more tank surface space for more separation and purification equipment. When the tank surface space is sufficient, the customer can also choose a centrifuge to reduce the ultra-fine solid phase in the drilling mud to avoid the ultra-fine solid phase from being concentrated in the drilling mud. GN Solids Control not only has standard model solids control system optional, but also provides custom designed mud recovery system for customers to purchase. If you have any such requirements, please feel free to contact us.

Recently, GN Solids Control shipped a set of sludge treatment system to a China domestic customer. At present, the system has been completely installed and commissioned.

This sludge treatment plant is mainly used for recovering oil from industrial oily sludges such as oily sludge produced at the drilling site, and oil sludge from refinery tank cleaning. After treatment, the recovered oil can be used as fuel or sold for profit; the oil content in the recovered water and solids is small, and it is easy to detoxify by further processes.

The GN Solids Control sludge treatment system is a stepped three-phase separation system. It mainly consists of the following modules:

Premixing module — The premixing module is used to collect sludge. Different sources of sludge have different solid contents and different viscosities. This will pose a huge challenge to sludge treatment. The GN Solids Control sludge separation system requires the solids content of the feed sludge to be less than 20%. Therefore, in the mixing module, the operator needs to add water to dilute the sludge, and at the same time, the chemicals and the diluted sludge can be fully mixed and stirred.

Large particle separation module-A drilling fluid shale shaker is installed in this module to remove large particles of solids in sludge, thereby reducing solids content. This procedure can greatly reduce the workload of subsequent sedimentation centrifuges.

Solid-liquid separation module-a decanter centrifuge in this module is used to remove fine particles from the material. This module mainly separates the mixed liquid (water-oil mixture) and solids. The separated sludge is returned to the homogenizer for washing, and the liquid is sent to the next step for further processing.

Three-phase separation module-disc high-speed separator is used for three-phase separation of oil, water and ultra-fine solids. During this process, the solid content of the feed mixture should be less than 3%, and the solid size should be less than 400 microns.

For the transportation of sludge materials, we recommend the use GN vacuum pumps, which are suitable for high-risk gas explosion-proof areas. In addition, we also provide container-type chemical dosing devices for adding chemicals to sludge treatment systems.

For more information on sludge treatment systems, please feel free to contact us.

Non-excavation mud clean system is an important part of the GN Solids Control system. Based on its compact structure, small footprint and high efficiency, it is widely used in mud treatment in urban infrastructure construction. As a country with rapid development of infrastructure construction, the construction of underground pipeline networks in urban infrastructure construction in India has also become very busy. Underground pipeline network construction is carried out by non-excavation companies after winning the bid, so non-excavation companies generally have multiple rigs and purification systems. Generally, each drilling rig needs to be equipped with a mud recovery system, corresponding to the processing capacity of the related drilling rig. GN Solids Control has exported multiple HDD mud recovery systems to India.

The standard non-excavation mud recovery machine system consists of mud recovery equipment, mud mixing equipment and mud collection tanks. Unlike the mud recovery device in the oil and gas drilling industry, non-excavation drilling first discharges the mud back to the mud pit on the ground, and then uses a vertically installed submerged slurry pump to transfer the mud to the mud recovery system. Purification system, Shale Shaker, Desander, Desilter, and progressive removal of rock cuttings and solid waste. This is a standard configuration. If there are higher separation requirements, we will add a centrifuge to the system as a fourth-stage processing equipment to control the solid particle diameter of the slurry at 5-10 microns.

The size of the mud tank usually depends on the size of the rig and the volume of mud that needs to be stored. On the mud tank, a stirrer and a mud gun are needed to stir the mud to suspend the solids in the mud. To configure the proper mud, a jet mixing system is needed to add chemicals to maintain the properties of the mud.

GN Solids Control high-profile mud recovery bears have different sizes and design schemes and are widely used in oil and gas drilling, non-excavation drilling, piling, TBM and other separation projects. GN Solids Control is pleased to provide you with professional products and configuration information about mud recovery systems, please feel free to contact us if you are interested.

For more information on GN Solids Control, please feel free to contact us.

GN Solids Control drill cutting dryer is widely used in oil-based mud drilling sites around the world. Recently, our after-sales engineers conducted customer return visits to several sets of drill chip dryers sold to Xinjiang. Received good reviews from customers.

The drill cuttings dryer is designed to further process the cuttings discharged from the shale shaker of the solid control system to recover more drilling mud and reduce waste emissions. Greatly reduce waste disposal costs and save consumption of drilling fluid base fluid. GN Solids Control vertical cuttings dryer can reduce the oil content of cuttings(OOC) to less than 5%.

GN Solids Control can provide screw conveyors for receiving and feeding, or drill cutting conveying pumps. Drilling cutting dryer, decanter centrifuge, slurry feed screw pump, installation tank and bracket, discharge screw conveyor and corresponding quick-mount bracket. Meet the requirements of customers’ overall solutions.

1: Screw Conveyor——According to the layout of the on-site mud recovery system, GN Solids Control provides lifting support legs for screw conveyor installation, which are used to collect drilling debris from the mud system, especially the first-level shale shaker, and transport it to the rock cuttings. Dry machine. If more flexible equipment layout is needed on site, GN Solids Control recommends replacing the screw conveyor with a sludge vacuum pump.

2: Rock cuttings dryer-Rock cuttings dryer is the key equipment of the system. It is used to shake off the oil and liquid in the cuttings by centrifugal force, thereby reducing the oil content of the cuttings by less than 5%. GN Solids Control’s cuttings dryer is equipped with an air knife and flushing system to ensure that the dryer runs for a long time without blocking the screen basket. Speeds of up to 900 rpm ensure the dryness of the cuttings discharged from the cuttings dryer.

3: High-speed Decanter centrifuge—The liquid discharged from the drill cuttings dryer is pumped to the Decanter centrifuge for processing, removing ultra-fine solids, so that the drilling fluid can continue to be used for drilling.

In addition to the integrated drilling drying system, GN Solids Control can also provide a modular design, that is, each equipment is equipped with a corresponding installation tank or bracket, which is convenient for customers to make different combinations or use equipment individually according to the working conditions.

For more information on GN Solids Control, please feel free to contact us.