Author: admin

One of the largest Oil Gas Directory Rigzone list GN Solids Control in their online directory.

Rigzone Directory Notification as below:

Congratulations – your company website (www.gnsolidscontrol.com) is the newest addition to Rigzone’s Online Oil and Gas Directory! After careful review by Rigzone’s editors, your site was approved. Your site listing will be available at search.rigzone.com within 3-5 business days.

Our list in Rigzone:GN Solids Control

GN Solids Control Products & Services in Rigzone directory:

Products >> S >> Solids Control >> Degasser

Products >> S >> Solids Control >> Desanders

Products >> S >> Solids Control >> Desilters

Products >> S >> Solids Control >> Shakers

Products >> S >> Solids Control >> Centrifuges

Products >> T >> Tanks >> Mud

Products >> M >> Mixers

Directory Categories

Companies >> Manufacturers & Suppliers >> Solids Control

Who visits Rigzone?
Rigzone’s vibrant, quickly growing audience and member base spans the upstream oil and gas industry from major corporate executives to influential independents.

• Drilling rig owners and operators
• Offshore support services (tugs, tenders, caterers, parts suppliers, etc.)
• Oil and gas industry executives from large multi-nationals to smaller independents
• Oil and gas industry human resources directors and departments
• Oil and gas industry workers and job seekers of all skill levels and areas of expertise
• Parts and equipment manufacturers, distributors, and suppliers
• Investors and analysts involved in the oil and gas industry

What does Rigzone offer?
Rigzone provides its visitors and membership with an unequaled source of information – a true industry gateway full of dynamic, original content and resources that cannot be found anywhere else.

• Online Oil & Gas Directory – the industry’s most complete listing of online oil and gas industry companies and related services
• Offshore Rig Data Services – continually updated status and location information on the world’s offshore drilling fleet
• Offshore Permits Service – daily and weekly offshore drilling permits and plans for the Gulf of Mexico, Texas, and Louisiana
• Career Center – a vibrant community of job seekers and employers in the oil and gas industry
• Classifieds Marketplace – online forum for buying and selling new and used goods and services
• Data Services – up-to-date news and information, rig usage reports and trend analysis, and much more
• Financial Information & Analysis – an industry specific guide to the financial positions and important information for the oil and gas industry’s publicly traded corporations
• Newsletter Service – weekly updates to your inbox full of news and commentary, rig information, and more

Sand Pump in China with Models,we usually call SB series Sand Pump.Since In Chinese,Sand Pump is Call Shabeng, So we select the first letter as “SB Sand Pump“.

Explanation of SB Sand Pump  model

SB 8 × 6 — 14

• SB :Sand pump code

• 14:Sand Pump Impeller diameter

• 6:Sand Pump Export diameter

• 8:Sand Pump Inlet diameter

SB series oilfield  Sand Pump Technical Parameters

Model	Flow	Lift	Power	Speed	Efficiency
SB8×6-14	320 m3/h	40m	75kW	1480/r/min	65%
SB8×6-13	240 m3/h	35m	55kW	1480/r/min	64%
SB8×6-12	216 m3/h	30m	45kW	1470/r/min	64%
SB6×5-14	200 m3/h	40m	55kW	1480/r/min	62%
SB6×5-13	180 m3/h	35m	45kW	1470/r/min	60%
SB6×5-12	200 m3/h	30m	37kW	1460/r/min	62%
SB5×4-14	120 m3/h	40m	37kW	1460/r/min	56%
SB5×4-13	90 m3/h	40m	30kW	1460/r/min	56%
SB4×3-12	60 m3/h	20m	11kW	1450/r/min	54%
SB4×3-11	40 m3/h	20m	7.5kW	1450/r/min	49%

SB Sand Pump Operations

A. Preparations

(A). Inspect the rotating direction

(B). Rotate the pump shaft by hands and ensure that it rotates smoothly

(C). Fully open the valve at suction section.

(D). Fully fill the pump and suction piping with liquid in order to eliminate air in them.

(E). Open all the cooling water-pipes.

(F). Lightly open the valve in delivery pipe system (if using a vacuum pump for priming, the valve must be fully closed before starting the main pump).

B. Operation for Running Sand Pump

(A). Start up the motor after all the preparations is finished.

(B). Gradually open the throttle valve of outlet after the pump pressure is stable and close it if no liquids flowing out. Gradually re-open it after the pressure is stable and until the capacity is normal.

(C). Operating conditions

a.Speed:1480r.p.m

B.Max Pressure: 10.5Kgf/cm²

c.Max Temperature:120℃

Sand Pump is the ideal equipment to provide impetus for Desander 、Desilter and Jet Mud Mixer. It can also be used as Charge Pump auxiliary perfusion for mud pump and Trip Pump for drilling well head

Welcome to contact us for quotation,and consultant of SB Sand Pumps.

JBQ mud agitator is a part of solid control system of mud tank, which is mainly used in agitating and blending drilling fluid so as to control the depositions of solid particles in its tank cycling system and keep the drilling mud property of circulation stable and mixture uniform.The drilling mud agitator are required for storage mud tanks,and mud tanks

with solids control equiments.

Learn more about the specs for GN: Drilling mud agiator

JBQ Drilling mud agitator has some major features as following:

(1)       The reducer of the agitator adopts a cylindrical worm with an axial section of circular acre. The circular acre teeth of impeller wheel are conjugated with the worm, which provide good convexo-concave engagement, high efficiency transmission, strong agitating ability and compact structure.

(2)       The reducer of the JBQ drilling mud agitator  combines with anti-explosion motor, which is suit for rough operation condition in field, and can be repaired conveniently.

(3)        New up-down structural agitating impeller wheels have a two-layers structure, which can be used as one-layer and dual-layer one.

(4)       The strong agitation, broad conformance and low starting moment of resistance are provided.

(5)        The drilling mud agitator Level – placed motor is easy for installation, adjustment and replacement.

As 1 of top 10 China solids control manufacturer,we also design complete equipments for horizontal directional drilling mud system.Get competitive price,top quality mud agitators from GN solids control.

The drilling mud cleaning system are required in oil well drilling,horizontal drilling,the mud cleaning system fuction is for preparing clean mud for drilling rig.

Generally,The mud cleaning system for removal of drill cuttings and recovery of drilling mud coming from an oil well, where the mud slurry may be made up essentially of barite particles having a specific gravity of 4.2 or more and a particle size mostly under 200 mesh, drill cuttings having a specific gravity of 2-3, and varying particle sizes ranging from 200 mesh to 1/2 inch or more, and water;

• In oil well drilling, drilling mud must be supplied to the hole as the well depth progresses. One of the basic functions of drilling mud is to carry the drill cuttings up to the surface so they can be disposed of. A drilling mud in common use today is typically composed of barite and water. There may be other constituents, (such as oil) but they would exist only in small amounts or percentages. Since large quantities of drilling mud are needed in drilling an oil well, it is desirable to recover the barite, and recycle it. Various drilling mud cleaning systems are in use today for separating the drill cuttings from the slurry so that the fluid and/or barite can be recycled. Most systems use a combination of one or more screens or sieves in a series flow relationship, with a final separating step using a hydrocyclone or centrifuge. Hydrocyclones desander and decanting centrifuges are expensive pieces of equipment with high energy and maintenance costs.

• In HDD drilling mud cleaning system,sometimes there is a single tank, closed-loop system or a multi-tank mud system is required, GN Solids Control can develop the proper system to meet specific requirements. from small HDD (hirontal directional drilling mud system) to deep oil well drilling mud system.

When design HDD drilling mud mixing tank,and storage tanks,when should take the following items for consideration.
The pictures are :Drilling Mud mixing tanks for export

Welcome to Consult us for HDD drilling mud tanks or mud system design as well as oilfield drilling solids control system design.Cost-effective solutions are guaranteed .

• All Mud Tanks to be equipped with agitators with sufficient turnover rate to prevent settling mud.
• All drilling mud tanks shall be equipped with level sensors.
• Electrical equipment shall be suitable to be located in zone oilfield  environment.
• The chemical dosing system shall consist of 5 feeding stations where 4 stations are combined for dry bulk and liquid.
• The feeding stations shall be able to feed into two separate mixing lines. The unit shall be able to handle single sacks.
• The chemicals shall be transported, stored and mixed without any risk for spillage orharmful exposure for personnel.
• The drilling mud tanks shall be completely covered and ventilated with inspection hatches.
• The HDD (Horizontal directional drilling ) mud tank design shall ensure easy cleaning and easy access.

• The H.P. shear unit shall be located in the mud  mixing tank, chemical mixing tank, and one storage tank.Two separate mixing lines shall be available simultaneously to familitate mixing in both the active and storage system.
• The triptank shall be designed to measure volume variance down to 0.1m3. Measurement by two independent systems.

GN Solids Control design manufacture and export drilling mud mixing tanks and drilling mud storage tanks internationally.Welcome to contact us to consult for design and manufacture drilling mud tanks.

We also design HDD drilling mud tanks mounted with Equipments like desander,desitlers,or mud cleaners.

Each drilling  mud tank shall have possibility to be isolated from the system during maintenance.
he agitator gearboxes to be greased. One drilling mud storage tank and the slug tank to be designed for 2.0 s.g. mud. The reminding tanks shall be designed for 1.8 s.g. mud.

GN desilter is manufactured by GN Solids Control .We design and manufacture desilter for separating drilling

fluids,drilling mud.

• Hydrocyclone desilter Assembly

1. Connect the grout outlet of sand pump and admission inlet with 6″ rubber pipe. The gas hole installed on the top of overflow pipe is used for preventing the siphon effects. A little drilling fluid will be flowed from air-bleed hole when the desilter is running. Air-bleed hole can not be blocked. If not, desilter will be failed to run.
2. Manifold of desilter: Two ends of incoming-stream manifold and overflow manifold should be connected with flange, in which the liquid can flow. The joint of overflow pipe can be rotated in any angle along the axle, through which the 8″ rubber pipe can be fixed in other drilling liquid tank easily. Incoming-stream pipe and overflow pipe of hydrocyclone should be assembled with 90° angle.
3. Firstly, open the fixed equipment of desilter screen box.
4. The operation of desilter is adjusted through the outlet pressure of sand pump.
5．Desilter Screen Assembly
The quality of installation will influence its life and running. Don’t damage the screen artificially and loosen the screen when assembling. If not, the sound “FLAPPING” will be emerged between screen and support rubber strip when shale shaker is running, in which the screen is damaged speedily. However, don’t stretch it tightly. If not, the pre-force of screen is exceed, in which the damaged degree of screen also be speeded or the screen is stretched directly.
If the support rubber strip of screen box is rugged or damaged, press and change it.
6．Slip locking equipment
This equipment locks the roll-axial to tighten the screens. Lock in roll-axial through stretching the slip by bolts. Grease should be feed into the slip locking structure for every replacing of screen to prevent the equipment sticking.
7．The maintenance of desilter screens
Iron parts and other hard particles are forbidden to destroy or tear the screen.
The meshes of screen should be matched according to performance of well liquid. The finer screen(shale shaker screen) should be prior only if the well liquid is flown from the screen, in which the effects will be better.

• Hydroclone Desilter Maintenance

This Desilter should be maintained forcibly.
Adjust, clean, screw, and change part expired and damaged units if the operation exceeds 500 hours totally.
Check or change tight roll-axial of screen box， and change the cut-cone and spiral case, as well as check the insulation of motors if the operation exceeds 4000 hours totally.

Drilling fluids management system is a integration of different drilling fluids purification equipments like shale shakers,hydrocyclones,centrifuges etc.

GN Solids Control is 1 of about 10 China manufacturers who can design and manufacture all the equipments for a complete drilling fluids management system

All the drilling fluids management equipments are mounted over the drilling mud tank.

There are many ways to configure your mud tanks below your drilling fluids management equipment. The most common practice requires three sections. Under your shale shaker you have the first section known as the sand trap where the mud to be pumped from this section goes through your Desander. This cleaned mud is then dumped into the second section known as a silt tank. The mud is picked up then pumped through your Desilters. The Desilters dumps the cleaned mud into the third section, know as the clean mud or mixing tank. This will be picked up by  the pump to be pumped back into your bore hole.

To provivide Combination Desanders/Desilters are common when the volume being pumped is under 500 GPM. The tank separation in this drilling fluids managemet application can be achieved with two sections in the mud tank. A clean section where mud to be mixed and pumped down hole is located. The second section is under the shale shaker where the contaminated mud is picked up and processed by the Desander/Desilter combination.

The drilling fluids management Equipments

• Drilling fluids Shale Shakers

The first line of defense for a properly designed drilling fluids management system has been and will continue to be, the shale shaker. Without proper screening of the drilling fluid during this initial removal step, reduced efficiency and effectiveness of all downstream drilling fluids management in the system is assured. The downstream hydrocyclones will simply be overloaded beyond their designed capacity.

• Drilling fluids Hydrocyclones

Hydrocyclones are simple mechanical devices, with out moving parts, designed to speed up the settling process. Feed pressure is transformed into centrifugal force inside the cyclone or cone to accelerate particle settling in accordance with Stoke’s Law #1. In essence, a cyclone is a miniature settling pit which alloys very rapid settling of solids under controlled conditions.Hydrocyclones have become important in drilling fluids management system because of their ability to efficiently remove particles smaller than the finest mesh screens.

• Drilling fluids decanting centrifuge

Decanter centrifuge are used to process unweighted and weighted, water-based and oil-based drilling fluids (muds). Mechanical energy is utilized to increase the gravitational force exerted on solids that are present in the mud system.oilfield Decanting Centrifuge are able to apply over 3,000 G-forces on the liquid/solids mixture, which separates the heavier solids from the lighter solids.

Other drilling fluids management equipments includes:centrifugal pump,drilling fluids degasser,etc.

Contact GN Solids Control for complete drilling fluids management system solution.

GN Solids Control design and manufacture complete mud tank system for customer internationally.

To get material of -500 mm + 0,015 mm when solid rate of the pulp is under 30%,our ZQJ 250×100 Mud Cleaner(conbination of linear motion shale shaker+desander+desilter) will work well for your application. Because, the viscosity of drilling fluids is high since it contains clay,and bentonite. When mud viscosity is low,the separation effect will be better.

To separate different rangle of particles,if particle size rangle you need is not very big as we thought when study the info. you sent us,we can design a complete mud tank system use different mud separation equipments like shakers,desilters,desanders,centrifuges.And also we can adjust the separation particle size rangle by using different mesh screens,different speed centrifuges.The specs in our brochure is for normal models.

We enclosed the complete mud tank system from big to small for your info.

We have the following questions for propasal of our separation equipments & system:
1,Different rangles of particle size you need to get?
2,The treating capacity of the mud you require,eg. 200 m3/h ?
3,The solid rate of your mud?

Then will design a complete mud tank system for your application.

Customer reply:

Below; first of all, we want to give the answers of your 3 questions.
1-The range of the particle size we aim to get is;
Maximum Size 0,5mm
Minimum Size 0,005mm (5 microns)
2-The treating capacity of the mud we require is; between 200m3/h – 250m3/h.
3-The solid rate of our mud would be maximum 30%.
Currently, we continue flotation test works in order to fix the absolute particle size and the absolute pumps and machines capacities.

We would like to state that we are quite pleased to cooperate with GN Solids Control and looking forward to have your engineer in November in Turkey.

After we get the result,we’ll keep gn solids control blog updated about this deal,and provide the solutions about what complete mud tank systems we privided.

GN oilfield drilling mud Desilter is discussed for application in mining slurry separtion.

Thank you for your e-mail of 12th October about your solids control equipments application.

We are of opinion that, during your interpretation of the technical specifications and the screen analysis of our ore, a misunderstanding must have occurred.

The result of the screen analysis of our ore we sent to you was only to give you a general information about the grain size of the ore.

These grain sizes do not reflect the particle sizes which we will feed into our process line.

The ore we are going to feed into the concentrator will preliminarily be screened through a 0,500 mm (35 mesh U.S) screen and be reduced down to -0,500 mm.

Following this, -0,500 mm material will be deslimed by separating ≥15µ using Hydrocyclone desilter and in this way we will end up with a material of -500 mm + 0,015 mm.

Studying the technical parameters of your ZQJ DESILTER, we understood that we can deslimed our (-0,500mm) material, by separating it at ≥ 15µ, using your ZQJ DESILTER.

During this operation we think that the solid rate of the pulp should be approximately 15%.

We are waiting for your answer, stating, if it would be possible to apply the process given above successfully using your DESILTER.

We can discuss and negotiate the details about your other equipment like shale shakers,decanting centrifuges, machinery and pump after having finished the negotiations about the applicability of DESILTER.

As a oil gas industrial equipments manufacturer,GN Solids Control sales team keeps visiting to Top 5 oil gas industrial information news website to keep informed about petroleum industry.We list Top 5 website as below.

• Top 1 website:http://www.rigzone.com

About Rigzone
Rigzone.com is “Your Gateway to the Oil and Gas Industry” providing you with industry news and information, the Online Oil & Gas Directory, careers, a classifieds marketplace, and more.

Welcome to contact GN Solids Control for oilfield drilling solids control equipments.
Who visits Rigzone?
Rigzone’s vibrant, quickly growing audience and member base spans the upstream oil and gas industry from major corporate executives to influential independents.

* Drilling rig owners and operators
* Offshore support services (tugs, tenders, caterers, parts suppliers, etc.)
* Oil and gas industry executives from large multi-nationals to smaller independents
* Oil and gas industry human resources directors and departments
* Oil and gas industry workers and job seekers of all skill levels and areas of expertise
* Parts and equipment manufacturers, distributors, and suppliers
* Investors and analysts involved in the oil and gas industry

• Top 2 website:http://www.offshore-mag.com

About Offshore Magazine
Offshore magazine, first published in 1954, is a monthly publication recognized as the worldwide leader for covering the key issues and trends relative to offshore technology, oil and gas E&P operations. It is the world’s most highly respected magazine dedicated entirely to the offshore industry, and enjoys the highest and most widely read circulation in its class. Since 1910, The PennWell Petroleum Group has been the industry leader for coverage of and service to the worldwide petroleum industry. Its foundation magazines are Oil & Gas Journal, Offshore, Oil, Gas & Petrochem Equipment, Oil & Gas Financial Journal, LNG Observer and The Petroleum Buyers Guide. The group also produces targeted e-Newsletters, hosts global conferences and exhibitions, seminars and forums, directories and technical books, print and electronic databases, surveys and maps.

• Top 3 website:http://www.pennenergy.com

About PennEnergy
PennEnergy serves global energy professionals with the broadest, most complete coverage of industry-related information, with resources to help effectively perform critical job functions.

Including content from all PennWell Petroleum brands and other industry sources, PennEnergy.com delivers original industry news, financial market data, in-depth research, maps, surveys, statistical data, and equipment/service information. We have also invested in Google search technology to make it easy for customers to search and find needed data.

Since 1910, The PennWell Petroleum Group has been the industry leader for coverage of and service to the worldwide petroleum industry. Its foundation magazines are Oil & Gas Journal, Offshore Magazine, Oil, Gas & Petrochem Equipment, Oil & Gas Financial Journal, LNG Observer and The Petroleum Buyers’ Guide. The group also produces targeted e-Newsletters, hosts global conferences and exhibitions, seminars and forums, directories and technical books, print and electronic databases, surveys and maps.

• Top 4 website:http://www.worldoil.com

ABOUT WORLD OIL ONLINE
World Oil, established in 1916 as The Oil Weekly, is published monthly by Gulf Publishing Company.  For over 90 years, the World Oil team has maintained a shared vision – to offer superior editorial content in World Oil that covers the Upstream Oil and Gas Industry by “Defining Technology for Exploration, Drilling and Production.”  World Oil brings buyers and sellers together via World Oil’s superior circulation and online exposure and achieves advertiser’s confidence by delivering cost-effective results.

• Top 5 website: http://www.upstreamonline.com

About Upstream Newspaper:
Upstream is an award-winning global oil & gas newspaper, published weekly and solely available on a subscription basis at an annual subscription fee of US$950.

Upstream’s influential readers are willing to pay for quality, that’s the philosophy. With an experienced team of 26 reporters located around the world, Upstream can provide the unbiased, independent journalism that readers praise so highly. Upstream is described as “invaluable”, “excellent” and “the best publication of its type on the market” by senior managers in some of the most respected companies in the industry.

Upstream has firmly established itself as the leading source of quality news in the international oil and gas industry.

Top drilling fluids supplier in the world