Mud Solids Control Equipment

GN Solids Control design and manufacture complete mud tank system for customer internationally.

To get material of -500 mm + 0,015 mm when solid rate of the pulp is under 30%,our ZQJ 250×100 Mud Cleaner(conbination of linear motion shale shaker+desander+desilter) will work well for your application. Because, the viscosity of drilling fluids is high since it contains clay,and bentonite. When mud viscosity is low,the separation effect will be better.

To separate different rangle of particles,if particle size rangle you need is not very big as we thought when study the info. you sent us,we can design a complete mud tank system use different mud separation equipments like shakers,desilters,desanders,centrifuges.And also we can adjust the separation particle size rangle by using different mesh screens,different speed centrifuges.The specs in our brochure is for normal models.

We enclosed the complete mud tank system from big to small for your info.

We have the following questions for propasal of our separation equipments & system:
1,Different rangles of particle size you need to get?
2,The treating capacity of the mud you require,eg. 200 m3/h ?
3,The solid rate of your mud?

Then will design a complete mud tank system for your application.

Customer reply:

Below; first of all, we want to give the answers of your 3 questions.
1-The range of the particle size we aim to get is;
Maximum Size 0,5mm
Minimum Size 0,005mm (5 microns)
2-The treating capacity of the mud we require is; between 200m3/h – 250m3/h.
3-The solid rate of our mud would be maximum 30%.
Currently, we continue flotation test works in order to fix the absolute particle size and the absolute pumps and machines capacities.

We would like to state that we are quite pleased to cooperate with GN Solids Control and looking forward to have your engineer in November in Turkey.

After we get the result,we’ll keep gn solids control blog updated about this deal,and provide the solutions about what complete mud tank systems we privided.

GN oilfield drilling mud Desilter is discussed for application in mining slurry separtion.

Thank you for your e-mail of 12th October about your solids control equipments application.

We are of opinion that, during your interpretation of the technical specifications and the screen analysis of our ore, a misunderstanding must have occurred.

The result of the screen analysis of our ore we sent to you was only to give you a general information about the grain size of the ore.

These grain sizes do not reflect the particle sizes which we will feed into our process line.

The ore we are going to feed into the concentrator will preliminarily be screened through a 0,500 mm (35 mesh U.S) screen and be reduced down to -0,500 mm.

Following this, -0,500 mm material will be deslimed by separating ≥15µ using Hydrocyclone desilter and in this way we will end up with a material of -500 mm + 0,015 mm.

Studying the technical parameters of your ZQJ DESILTER, we understood that we can deslimed our (-0,500mm) material, by separating it at ≥ 15µ, using your ZQJ DESILTER.

During this operation we think that the solid rate of the pulp should be approximately 15%.

We are waiting for your answer, stating, if it would be possible to apply the process given above successfully using your DESILTER.

We can discuss and negotiate the details about your other equipment like shale shakers,decanting centrifuges, machinery and pump after having finished the negotiations about the applicability of DESILTER.

As a oil gas industrial equipments manufacturer,GN Solids Control sales team keeps visiting to Top 5 oil gas industrial information news website to keep informed about petroleum industry.We list Top 5 website as below.

• Top 1 website:http://www.rigzone.com

About Rigzone
Rigzone.com is “Your Gateway to the Oil and Gas Industry” providing you with industry news and information, the Online Oil & Gas Directory, careers, a classifieds marketplace, and more.

Welcome to contact GN Solids Control for oilfield drilling solids control equipments.
Who visits Rigzone?
Rigzone’s vibrant, quickly growing audience and member base spans the upstream oil and gas industry from major corporate executives to influential independents.

* Drilling rig owners and operators
* Offshore support services (tugs, tenders, caterers, parts suppliers, etc.)
* Oil and gas industry executives from large multi-nationals to smaller independents
* Oil and gas industry human resources directors and departments
* Oil and gas industry workers and job seekers of all skill levels and areas of expertise
* Parts and equipment manufacturers, distributors, and suppliers
* Investors and analysts involved in the oil and gas industry

• Top 2 website:http://www.offshore-mag.com

About Offshore Magazine
Offshore magazine, first published in 1954, is a monthly publication recognized as the worldwide leader for covering the key issues and trends relative to offshore technology, oil and gas E&P operations. It is the world’s most highly respected magazine dedicated entirely to the offshore industry, and enjoys the highest and most widely read circulation in its class. Since 1910, The PennWell Petroleum Group has been the industry leader for coverage of and service to the worldwide petroleum industry. Its foundation magazines are Oil & Gas Journal, Offshore, Oil, Gas & Petrochem Equipment, Oil & Gas Financial Journal, LNG Observer and The Petroleum Buyers Guide. The group also produces targeted e-Newsletters, hosts global conferences and exhibitions, seminars and forums, directories and technical books, print and electronic databases, surveys and maps.

• Top 3 website:http://www.pennenergy.com

About PennEnergy
PennEnergy serves global energy professionals with the broadest, most complete coverage of industry-related information, with resources to help effectively perform critical job functions.

Including content from all PennWell Petroleum brands and other industry sources, PennEnergy.com delivers original industry news, financial market data, in-depth research, maps, surveys, statistical data, and equipment/service information. We have also invested in Google search technology to make it easy for customers to search and find needed data.

Since 1910, The PennWell Petroleum Group has been the industry leader for coverage of and service to the worldwide petroleum industry. Its foundation magazines are Oil & Gas Journal, Offshore Magazine, Oil, Gas & Petrochem Equipment, Oil & Gas Financial Journal, LNG Observer and The Petroleum Buyers’ Guide. The group also produces targeted e-Newsletters, hosts global conferences and exhibitions, seminars and forums, directories and technical books, print and electronic databases, surveys and maps.

• Top 4 website:http://www.worldoil.com

ABOUT WORLD OIL ONLINE
World Oil, established in 1916 as The Oil Weekly, is published monthly by Gulf Publishing Company.  For over 90 years, the World Oil team has maintained a shared vision – to offer superior editorial content in World Oil that covers the Upstream Oil and Gas Industry by “Defining Technology for Exploration, Drilling and Production.”  World Oil brings buyers and sellers together via World Oil’s superior circulation and online exposure and achieves advertiser’s confidence by delivering cost-effective results.

• Top 5 website: http://www.upstreamonline.com

About Upstream Newspaper:
Upstream is an award-winning global oil & gas newspaper, published weekly and solely available on a subscription basis at an annual subscription fee of US$950.

Upstream’s influential readers are willing to pay for quality, that’s the philosophy. With an experienced team of 26 reporters located around the world, Upstream can provide the unbiased, independent journalism that readers praise so highly. Upstream is described as “invaluable”, “excellent” and “the best publication of its type on the market” by senior managers in some of the most respected companies in the industry.

Upstream has firmly established itself as the leading source of quality news in the international oil and gas industry.

Top drilling fluids supplier in the world

Centrifugal pump is also called sand pump,GN Solids Control supply centrifugal pump from our China factory.Get centrifugal pump at Best price,Fast service.

Get centrifugal pump tech specs here:Sand pump
Definition of centrifugal pump
Machine for moving fluid by spinning it using a rotating impeller in a casing with a central inlet and a tangential
outlet

Note of Centrifugal pump:

NOTE The path of the fluid is an increasing spiral from the inlet at the centre to the outlet, tangent to the impeller annulus.
In the annular space between the impeller vane tips and the casing wall, the fluid velocity is roughly the same as that of
the impeller vane tips. Useful work is produced by the pump when some of the spinning fluid flows out of the casing
tangential outlet into the pipe system. Power from the motor is used to accelerate the fluid entering the inlet up to the
speed of the fluid in the annulus. Some of the motor power is expended as friction of the fluid in the casing and impeller.

These centifugal pumps are developed and fabricated  as supporting pumps based on requirement of transferring oil & gas drilling fluid. Centrifugal pump adopt the axial sucking structure and all the hydraulic components are wear proof cast iron, which is suitable for delivering the corrosive liquids with suspended particles in well drilling. Its quality is accepted by Weatherford and assembling dimension is same to Mission centrifugal pump.

SB centrifugal pumps are characteristic of abrasion resistance, smooth and stable running, reliable sealing, long service life and convenient maintenance.  Those pumps have been used for land and offshore drilling platforms in more than 20 countries over the world.

Clockwise pumps and anti-clockwise pumps are available.

Mechanical seal and compound seal are available. The compound seal adopts auxiliary impeller, special oil seal and packing seal. Main seal of mechanical  seal is mechanical seal with a long service life, auxiliary seal of machine seal is packing seal to prevent occurrence of accidents.
Shaft seals are lubricated with grease and bearings are lubricated with machine oil and grease  Since bearing covers at two ends of bearings are equipped with grease injectors.

Both inlet flanges and outlet flanges for centrifugal pump are with two series standard dimensions.

Centrifugal pump are widely used in oilfield drilling equipments and drilling mud equipments like shale shakers,desanders desilters etc.Top China  Centrifugal Pump company for drilling mud,welcome to consult us for centrifugal pump for oilfield drilling projects.We supply centrifugal pump worldwide.

Drilling mud treating system is for processing drilling fluids and,drilling mud treatment  is for disposal Contaminated drilling fluids and mud.

GN Solids Control is one of about ten china manufacturers who can design and manufacture all the equipments for a complete drilling mud treating system

Products:Drilling mud recycling equipments system

• Drilling Mud Treating System

To overcome many of the limitations of current solids-removal techniques, Drilling fluids mud-treating system was developed for weighted muds. The drilling mud or fluids treating system, called the Mud Cleaner, removes most of the drilled solids while retaining most of the barite and liquid phase of the mud. Unlike most barite-reclaiming or solids-removal techniques normally employed only after the drilled solids have reached an undesirable level, the Mud Cleaner is most effective when used as soon as barite is added to the mud system, and continuously thereafter. Continuous operation removes solids before they disintegrate to silt or clay size, thus preventing drill solids from accumulating in the mud treatment system. Briefly, the drillling fluids mud-cleaning system involves processing the mud through three separate stages:
(1) mud processing the mud through three separate stages: (1) mud at well-circulation rate flows through a first screen (shale shaker), which removes large-size solids; (2) the mud passes through a centrifuging stage (desilters), which passes through a centrifuging stage (desilter), which separates the mud into a low-density effluent and a high-density underflow – the effluent, comprising most of the liquid phase, returns to the mud treatment system; and (3) the underflow, containing barite and drilled solids, flows through a second, smaller  screen that is sized to pass the barite but to reject most of the drilled solids. The first screen can be provided by a conventional shale shaker that usually has a screen size between about 10 and 80 mesh. For most wells, shaker screens finer than 80 mesh are not capable of handling mud at normal well circulation rates. This means that mud passing the shale shaker contains large amounts of drilled solids. These solids upset mud properties and are the most difficult to remove. By pumping the mud tough desilters and screening the underflow, a large part of these fines can be removed without appreciable loss of barite.

• Treatment of Drilling Fluids and Drilling Mud

Contaminated drilling fluids and mud are a considerable potential hazard to the sensitive marine ecosystem. The appropriate process treats the contaminated fluids and muds sufficiently so that by the end of the process, purified and thus unpolluted water can be discharged into the environment. This task is performed by the high-speed decanters and clarifiers from GEA Westfalia Separator.

Drilling fluids are understood to be viscous emulsions which are circulated through the drilling pipe during drilling for crude oil in order to pump the milled product upwards at the same time as the oil. These emulsions rapidly become contaminated with mud, salt water and oil residues. This means that the drilling fluids have to be continuously cleaned to ensure a smooth drilling process. The contaminated fluids are also a hazard to the sea, however, so continuous treatment is all the more important.

Once the drilling fluids have passed through a coarse screen and had a flocculant and a flush liquid added, the coarser solids are separated off by a decanter of the appropriate output. The liquid phase is initially passed to a slop oil tank. A clarifier from GEA Westfalia Separator then separates the fine residual solids so that the liquid phase can be discharged into the environment in the form of pure water after passing through a protective filter. This complies with the “zero emission”

Oil well drilling mud conditioner are manufactured in our China factory.We provide you with competitive price,best solutions for drilling mud condition.

The present invention relates to additives or conditioners for oil well drilling fluids, and more particularly to a boron-chrome lignosulfonate drilling fluid additive or mud conditioner.

GN Solids Control design and manufacture Drilling Mud Conditioner utilizes a combination of hydro cyclones and a linear motion shale shaker to separate solids from liquid. The combination of hydrocyclone cones utilized is dependent upon the specific application of duty. Cone combinations typically consist of a few desander cones (10-inch or 12-inch) and several desilter cones (4-inch).

The most commonly used drilling fluids are aqueous dispersions of clay. The drilling fluid or “mud” is pumped down a hollow drill string, through the bit at the bottom, and up the annulus formed by the hole or casing and the drill string to thesurface. After reaching the surface, various operations are performed on the drilling fluid to remove the cuttings and formation material thereform. The drilling fluid is then treated with additives to obtain a desired set of rheological properties,and is then pumped back into the well in a continuous circulating process.

A satisfactory drilling fluid must have various desired functions, such as gelling during temporary work stoppage and other functions well known in the art, which contribute to the success of the well drilling operation. In order to accomplishthese various functions, it has been found necessary to incorporate certain additives in the drilling fluid. Modified lignosulfonates derived from spent sulfite liquor obtained from the pulping of woods have proven to be effective additives forobtaining the desired properties in drilling fluids.

These cones are mounted above the screen deck of the linear motion  shale shaker. The mud is fed first through the hydrocyclones, where it subsequently cascades down over the shale shaker. The remaining solids, including barite, are returned to the active drilling mud system.

The screens used on the shale shaker determine the cut point for the mud conditioner unit. When weighted mud  are used, shaker screens are selected in a manner that ensures that the majority of the weight material is returned to the mud system. Typically, API 170 screens (>82.5 to 98.0 microns) are utilized to reduce the amount of weight material discarded by the screens.

Drilling mud conditioner are widely used in petroleum oil and gas exploration industry, no-dig engineering, geotechnical engineering, mine, metallurgy, coal, hydropower and many other industries.GN drilling mud conditioning equipment can be used in both onshore and offshore oilfield project.HDD Horinzontal directional drilling mud system

Bentonite Mud Recycling Equipment is also called drilling mud solids control equipment,usually,use linear  shale shaker,mud cleaners,and decanting centrifuges to recycle bentonite mud.

GN Solids Control Supply a complete list of Bentonite mud recycling equipments.

Bentonite is an absorbent aluminium phyllosilicate, generally impure clay consisting mostly of montmorillonite. There are a few types of bentonites and their names depend on the dominant elements, such as K, Na, Ca, and Al. As noted in several places in the geologic literature, there are some nomenclatorial problems with the classification of bentonite clays. Bentonite usually forms from weathering of volcanic ash, most often in the presence of water.

Sodium bentonite expands when wet, possibly absorbing several times its dry mass in water. Because of its excellent colloidal properties (see Odom ref below) it is often used in drilling mud for oil and gas wells and for geotechnical and environmental investigations.
Much of bentonite’s usefulness in the drilling and geotechnical engineering industry comes from its unique rheological properties. Relatively small quantities of bentonite suspended in water form a viscous, shear thinning material. Most often, bentonite suspensions are also thixotropic, although rare cases of rheopectic behavior have also been reported. At high enough concentrations (~60 grams of bentonite per litre of suspension), bentonite suspensions begin to take on the characteristics of a gel (a fluid with a minimum yield strength required to make it move). For these reasons it is a common component of drilling mud desander used to curtail drilling fluid invasion by its propensity for aiding in the formation of mud cake.

In industrial drilling field,bentonie mud recycling equipment are widely used.

We are a China exporter of Bentonite Mud Recycling Equipment for Indian, Russian,middle east.etc.Oilfield Company of the United States and Century Int’l Oilfield Equipments LLC of the United Arab Emirates etc. choose us as Bentonite Mud Recycling Equipment supplier.Our factory and company are Quality Management System ISO 9001-2000 certified.GN solids control operate international Bentonite Mud Recycling Equipment sales,service,manufacturing,distribution serivce.Buy Bentonite Mud Recycling Equipment from China manufacturer,good quality,best price

GN Solids Control design and manufacture Oilfield Decanter centrifuge with different speed types.

In oilfield drilling mud separation,The larger the centrifugal force, the finer the separated solids, so three types of speed decanter centrifuge can get according to separating factor.

a)     Low-speed oilfield decanter centrifuge: it is also called “barite recovery” centrifuge. Its separating factor is 500~700. To low-density solids, its separating point is 6~10μm. To high-density solids, its separating point is 4~7μm. This kind of centrifuge can be used for recovering barite.

b)    Medium-speed oilfield decanter centrifuge: its separating factor is 800 or so, solids of 5~7μm can be separated, so harmful solids can be separated from the mud, so that gravity and viscosity of the mud can be controlled. Most drill team will choose this kind of centrifuge at present.

c)High-speed oilfield decanter centrifuge: its separating factor is 1200~2100 or so, separating point is 2~5μm, it can remove harmful solids, control mud viscosity, it is usually connected with low speed centrifuge to make up a dual centrifuge system(See figure 3). In the system, low-speed centrifuge is installed at the first grade, barite separated
from it is discharged into mud tank to be recovered, liquid is drained into a surge drum first, and then be sent by a pump to high-speed centrifuge; the solid separated from high-speed centrifuge will be discharged out of the tank and the liquid is back to recirculation system. “Dual centrifuge system” can remove

GN Solids Control supply Oilfield Decanter centrifuge from China,Top quality,China price.

Today,A Mining company from turkey inquired us for Mining indutrial slurry separation equipments.

Download:Equipments Catalog

We are a Mining Company active in Turkey.
We continue investing on Mica, Feldspar and Heavy Minerals production from our major and significant sources, which we have already converted into Proven Reserve.
Our material is insitu weathered pyroclastic tuff and is made of sand, silt and clay.
Our quarry production is based on HYDROMINING Method, by which the material is transferred into the plant in muddy condition by means of pumps.
We have pinpointed your firm through internet for mining mud separation equipment.
In order to start a detailed communication, we would like to ask you please, to pass across as soon as possible the prices of the Mining indutrial slurry separation equipment given attached.

And he selected slurry separation equipment for mining as below.

slurry separation Shale Shaker

Mining slurry separation mud cleaner

Desander mud desilter

Decanting Centrifuge

High Speed Frequency Converter Centrifuge

Sand Pump

Jet Mud Mixer

Submersible Slurry Pump

GN Solids Control Manufacture All these Mining indutrial slurry separation equipment,supply and provide service around the world for mining mud separation.

Oil Field Drilling Equipments are composed of different kinds of oilfield equipment including drilling equipment, workover equipment and production equipment.The world’s famous standard for oilfield drilling equipments are API standard (The American Petroleum Institute (API).

• Drilling Rigs.

A drilling rig is a machine which creates holes (usually called boreholes) and/or shafts in the ground. Drilling rigs can be massive structures housing equipment used to drill water wells, oil wells, or natural gas extraction wells or they can be small enough to be moved manually by one person.hey sample sub-surface mineral deposits, test rock, soil and groundwater physical properties, and also can be used to install sub-surface fabrications, such as underground utilities, instrumentation, tunnels or wells. Drilling rigs can be mobile equipment mounted on trucks, tracks or trailers, or more permanent land or marine-based structures (such as oil platforms, commonly called ‘offshore oil rigs’ even if they don’t contain a drilling rig). The term “rig” therefore generally refers to the complex of equipment that is used to penetrate the surface of the earth’s crust.

• Solids Control Equipment

GN Solids Control is one of China leading manufacturer of solids control equipment

includes centrifuges, shale shakers, desanders, degassers, desilters, mud cleaners, agitators, mud gas separator, shearing pumps, and sand pumps etc.

• Workover Rigs.

Workover rigs  includes offshore and onshore workover rigs, which range from 150 HP to 1,000 HP. The service depth of our workover rigs usually equipped with Caterpillar diesel engines and Allison transmissions is from 8,000 ft to 30,000 ft.

• Drilling Equipment.

Drilling equipments including masts, substructures, drawworks, crown blocks, traveling blocks, hooks, hook blocks, swivels, rotary tables, and top drives. The rated load of our AC/VFD drive top drives is from 190 tons to 1,000 tons.

• Triplex Mud Pumps.

Triplex Mud Pumps is a reciprocating piston/plunger device designed to circulate drilling fluid under high pressure (up to 7500 PSI) down the drill string and back up the annulus.Triplex Mud Pumps come in a variety of sizes and configurations but for the typical petroleum drilling rig, the triplex (three piston/plunger) mud pump is the pump of choice. Duplex mud pumps (two piston/plungers) have generally been replaced by the triplex pump, but are still common in developing countries. A later development is the Hex pump with six pistons/plungers.

• Well Control Equipment.

Well Control Equipment includes Shaffer and Cameron type blowout preventers, which include annular and ram type BOPs. Also included in our well control equipment are BOP closing units, choke manifolds, and kill manifolds.

• Oil Country Tubular Goods.

Oil Country Tubular goods includes drill pipes, heavy weight drill pipes, drill collars, casing and tubing. Our drill pipes are usually should be in accordance with API Spec 5D and their sizes are from 2-3/8″ to 6-5/8″. The steel grades of the drill pipes include E75, X95, G105, and S135.