Mud Solids Control Equipment

Shale shaker,desander,sand pump,and decanter centrifuge are main equipments for drilling mud solids control,the flowing is the report of using conditions for 13 oil wells.

• Drilling fluids shale shaker

In 13 oil wells, 5 wells use ZS2×1.15×2/3P low-frequency shale shaker, two wells teams using QGZS-G4 Ⅱ high frequency shale shaker, six wells teams using the DHL-1 high-frequency shale shaker. Accounted for using the number of high-frequency screen 61.5%, compared with last year have more greatly enhanced. One QGZS-G4 Ⅱ high-frequency shale shaker for the newly introduced, are used in good condition.

• 2, Desander

In 13 oil wells, 5 wells teams using the NCS-300 × 2-type Desander, two wells teams using ZCSQ-250×2-type Desander, six wells teams using the ZQJ-250 ×2-type Desander; accounting for the use of the number of 38.46% and 15.39%, 46.15%. Compared to last year, not the magnitude of changes, only to add two new Desander use.

• 3, Sand pump

In 13 oil wells a total of 12 teams use the SB-200 wells electric sand pump, a well teams using the SB-6″×8″ electric sand pump. Compared with last year, out of the belt transmission-type sand pump at the same time, the introduction of a new type of mechanical seal type sand pump.

• 4,Decanter centrifuge

After many years of practical use and continuous upgrading of the decanter centrifuge has been raised from a variety of models of multiple manufacturers into a relatively neat two manufacturers of the three models (which LW450×1000-NJ-type centrifuge at the end of March 2003 to replace eliminated); separation factor reached 800 or more, speed at 1800r/min above are more capable in  separating Sand, but also  facilitate equipment maintenance and management.

An old customer asked us to supply the PNEUMATIC SPINNING WRENCHES for his oilfield service.Though the client know the contact info of the PNEUMATIC SPINNING WRENCHES manufacturer,but he gives us their contact info and ask us to buy and sell to them.

This is really what we call trust!!

Q254-250 PNEUMATIC SPINNING WRENCHES

The wrench is the best replacement of rotary rope (or chain). It is applied for the mechanized spinning operation. The applicable range of pipe diameter is wide, and it can be freely adjusted whenever necessary. There are two configurations for clamping mechanism: air tyre and air cylinder. There are two driving and controlling styles: pneumatic and hydraulic. The spinning wrench is designed and manufactured according to API Spec 7K “Specification for Drilling Equipment

As a solids control equipments to manufacturer,we keep giving our clients reliable service.And now we even win the trust of our customer for PNEUMATIC SPINNING WRENCHES.

As a drilling mud equipments and system manufacturer, now we have an inquiry for drilling mud cooler to integrated into our drilling mud system.

The drilling mud cooler specifications:
1. Mobile Drilling Mud Cooler
2. Minimum capacity is 900 GPM
3. The system completed by pumps & piping for temperatures ( Bottom Hole
Temperature at End Section ) below :
a. Type 1 well :
1. 26” phase 112°F
2. 17”1/2 phase 200°F
3. 12”1/4 phase 265°F
4. 8”1/2 phase 280°F
5. 6” phase 320°F @ 8600 ft TVD as TD
b. Type 2 well :
1. 26” phase 112°F
2. 17”1/2 phase 190°F
3. 12”1/4 x 14”1/2 315°F
4. 12”1/4 phase 335°F
5. 8”1/2 phase 390°F
6. 6” phase 410°F @ 12,100 ft TVD as TD
c. Type 3 well :
1. 26” phase 96°F
2. 18”1/2 phase 112°F
3. 14”1/2×17”1/2 175°F
4. 12”1/4×14”1/2 275°F
5. 10”5/8 x 12”1/4 365°F
6. 8”1/2 phase 395°F
7. 6” phase 415°F @ 12,200 ft TVD as TD
d. Type 4 well :
1. 26” phase 96°F
2. 18”1/2 x 22” 112°F
3. 17”1/2 x 20” 160°F
4. 14”1/2 x 17”1/2 255°F
5. 12”1/4 x 14”1/2 265°F
6. 10”5/8 x 12”1/4 290°F
7. 8”1/2 phase 370°F
8. 6” phase 425°F
If anybody who is able to supply the drilling mud cooler in China for the drilling mud system, please feel free to contact us for more info about the drilling mud cooler.

As a drilling mud agitator and sand pumps manufacturer, we inquiries from our international mud tanks manufacturer client asking for buying mud agitators and sand pumps from us. Because outsourcing mud agitators, and sand pumps will save their cost, and production price.

I am interested in the prices for the mud mixing pumps ( with explosion proof motors ) , 11 Kw and 15Kw agitators,sand pumps etc , as we are producers of mud tanks for the oil industry here in Libya.

As a mud tanks manufacturer, Our Company is working with all major oil Contractors in Libya , and are depending on orders from them.

The world crisis is affecting our part of the world too. Rig count here is down too
At the moment we have orders for 2 x 3,000 bbls drilling mud systems only – we will be looking for the equipment for them, but last time the conditions which we received from your Company ( also prices ) were not very different from the prices which we have for similar equipment from the United States. And you must understand , that in such case we are going to purchase from there – as reputable manufacturer.

To buy from your Company you must be much more aggressive in pricing and delivery conditions – please re-consider.
We are still interested in all mud tank additional equipment : mud agitators, mud guns, pumps and maybe shale shakers

I appreciated your call – you must understand , that our purchase will depend not only on the price , but  also on after sale services and spare parts availability , as we want to offer to our customers reliable products.

Please send me a Proforma Invoice – based on 20 ft volume container – C & F to Tripoli , Libya for the following :

1. 8 x 11 Kw mud agitators

2. 8 x 15 Kw mud agitators

3. 4 x 30 Kw sand pumps

4. 4 x 37 Kw sand pumps

5. 20 drilling mud guns

Consumables for above pumps – seals or mud guards.

We are looking forward to cooperating mud tanks manufacturers, we manufacturer equipments like mud agitators, sand pumps, shale shakers or centrifuge them.Work on win-win situation.

M-I Swaco Mud Cleaner are widely used in oilfield drilling around world.GN Solids Control can supply customized mud cleaner  for Replacement of M-I Swaco line of mud cleaners.

Buy M-I Swaco  replacement mud cleaner from GN,you’ll enjoy:

• Less operation cost,GN mud cleaner shaker screen are soft strip screen with duration for over 10 days,and only USD20 for 1 screens.
• Cusomized design for specific application from HDD mud system to oil gas drilling mud system.
• Most competive price:World class quality,China Competive Price,1 of 10 top manufacturers in Solids control.

The M-I SWACO line of mud cleaners consists of a two-stage separation process using a combination of hydrocyclones mounted over a mud shale shaker to operate as a single unit.

• M-I swaco 2-12 Mud Cleaner
• M-I swaco 2-12 4T4 Mud Cleaner
• M-I swaco 2-12 6T4 Mud Cleaner
• M-I swaco 2-12 8T4 Mud Cleaner
• M-I swaco 3-12 Mud Cleaner
• M-I swaco 6T4 Mud Cleaner
• M-I swaco 8T4 Mud Cleaner

Below is the Inquiry from customer for replacement of their M-I Swaco mud cleaner

1

ea

M-I SWACO 212/6T4 Mongoose Pt Mud Cleaner with Dual Motion Adjustable Shaker with wedge lock tensioners, two (2) 2 HP vibrator motors and one (1) 0.6 HP vibrator motor, 60 hz, 440-480 volt, ATEX

P/N:9672360-35E

If you want to quote an equivalent mud please specify brand and attach technical information (catalogue and tab maintenance)

Our solutions:

Gas Buster is called also called vacuum degasser in oilfield drilling fluids gas separating.

A  Gas Buster is a simple separator vessel used to remove free or entrained gas from fluids circulated in the wellbore, such as mud used during drilling operations. The gas buster typically comprises a vessel containing a series of baffles with a liquid exit on the bottom and a gas-vent line at the top of the vessel.

GN oilfield Gas Buster

Our oilfield Gas Buster operates on a “thin strata” principle. The drill mud enters the tank and forces it to flow and distributed to a layer of internal baffle plates engineered to allow the liquid inside the oilfield Gas Buster to flow as thin film and is exposed to the vacuum within the vessel. This layer of mud allows the gas to escape or break out of the mud . The vacuum pump releases the gas and discharge it to the disposal line. Mud exits the vessel under the action of the venturi and is returned to the mud system.

GN Gas Buster operates in three functions – mud circulation, vacuum creation and gas removal.  The Gas Buster  is used to remove the small entrained gas bubbles left in the mud by the mud/gas separator. These units are positioned downstream from mud/gas separators, gumbo removal equipments (if utilized), shale shakers and mud conditioners (if utilized), while hydrocyclone desander and Decanting centrifuges follow in the arrangement.

Gas Buster type

Vacuum tank degasser Type is the most common form of degasser. Vacuum tank degasser  can be horizontal, vertical or round vessel. A vacuum action is created to pull in the gas cut mud. When the liquid enters the tank it will flow and be distributed to a layer of internal baffle plates designed for the mud to flow in thin laminar film and is exposed to a vacuum that forces the gas to escape and break out of the mud.The vacuum pump moves the escaping gas from the vessel discharging it to the rig’s flare or environmental control system. Vacuum degassers are neccessory for drilling mud system in oilfield.

GN manufacture Mining exploratory drilling mud equipments,drilling fluids circulation system for recycling drilling mud.

Mining exploratory drilling requires that the borehole be stabilized while obtaining the maximum geological information from returning core or cuttings. The drilling fluid system design must be able to address some of the most challenging geologic conditions. From exploratory drilling to core recovery, the drilling fluid must maximize borehole stability, properly clean the hole and maximize core recovery.

GN Drilling mud system include a jet mud mixing hopper which mixes bentonite  easily to provide viscosity and suspension of cuttings and provides a high quality filter cake to aid in stabilizing the warehole.

GN drilling mud equipments for the system like the shale shakers,mud cleaners are always customized specially for convenience and cost-effective drilling.To help the drilling rig get the most efficiency.

GN drilling mud system for Mining exploration is specially designed for easy mixing. The mud system enhances the filtration control properties of a drilling slurry and also helps stabilize problem shakes.

If you want to learn more about our drilling mud equipments and system design for mining exploration drilling rig.Pls feel free to contact us.

How to get HDD Drilling Equipments at a beat price?It’s time for you to look for HDD Drilling Equipments For sale at the world crisis.

Now we have a suggestion for you to get a good price For HDD Drilling Equipments full package.You know in HDD drilling,the two main parts of the equipments are 1,HDD drilling rig,3,HDD mud equipments.

It would be wise idea to get the two parts from different HDD drilling equipments manufacturers.But it may not be convenient for you.

GN Solids Control solutions,As a HDD drilling mud equipments manufacturer,we are discussing with HDD drilling rig company in China about cooperation.You can contact either of us,but get the complete package for your HDD drilling equipments at manufacture price.

Complete HDD Drilling Mud Equipments From GN Solids Control

• Fluids Processing System
• Shale Shaker
• Mud Cleaner
• Desander
• Desilter
• Decanting Centrifuge

More about HDD Drilling
Directional boring, commonly called horizontal directional drilling or HDD, is a steerable trenchless method of installing underground pipes, conduits and cables in a shallow arc along a prescribed bore path by using a surface launched drilling rig, with minimal impact on the surrounding area. Directional boring is used when trenching or excavating is not practical. Directional boring minimizes environmental disruption. It is suitable for a variety of soil conditions and jobs including road, landscape and river crossings. Installation lengths up to 6,500’ (2,000m) have been completed, and diameters up to 56″ (1,200mm) have been installed in shorter runs. Pipes can be made of materials such as PVC, polyethylene, Ductile iron, and steel if the pipes can be pulled through the drilled hole.

Don’t wait,get HDD Drilling Equipments For sale now.

We got an inquiry for Mud Mixing/recycling system  for Oil/HDD/Drilling

Looking to buy Mud Recycling system specs like below:

Output: Up to 350 USgpm (1300 litres/min)
Cut Point: 16 microns
Capacity: 4000 US gallons (15,000 litres)
Pumps: Three 3 x 4″ centrifugal pumps with approx 22kW motors
Power: Integral control panel for all electrical functions.
Please quote price CIF Mumbai, India or Kolkata, India.

About GN Drilling Mud Systems/Mud mixing Equipments

GN Solids Control Mud delivers a wide range of modern, innovative and cost-effective mud systems and equipment for both on- and off-shore applications. Each piece of equipment is designed and manufactured with a strong focus on quality, reliability, flexibility, and ease-of-use.

An effective and reliable mud recycling system is a fundamental part of any modern drilling application; from mud mixing to mud treatment, low pressure and high pressure mud equipment, bulk storage to mud system control, TTS Sense Mud offers a full range of quality solutions designed to add value to your drilling project.

GN Drilling Mud equipment is custom-designed to individual project requirements and manufactured to the most rigorous standards, providing our customers with safe, cost-effective and reliable mud mixing, for oil gas drilling,Horizontal directional drilling.

Our Equipments for this Mud Mixing/recycling system of Oil/HDD/Drilling

S/n    Description    Quantity    Unit
1,    ZS63×125-3  Shale shaker 1
2,      ZQJ100×6 Mud cleaner 1
3,      SB4×3-13 Sand pump             1
4,      LSB4×3-13 Sand pump 1
5,      Mud Tank  6000×2500×2900mm    1
6,      Jet mixing hopper 1

Welcome to contact us for more customized  Mud Mixing/recycling System  for Oil/HDD/Drilling

GN Solids Control is an oilfield Decanter centrifuge China Based Manufacturer,our decanter centrifuge rangles from low speed to high speed,and we also supply virable decanter centrifuge for drilling mud.

LW355-1250N series of high speed centrifuge produced by our company can better meet the above requirements.
Model and technical parameters.

2.1 Centrifuge Model：GLW  355-1250N
High quality stainless steel made
Effective roller length 1250mm
Inner diameter of the roller 355mm

High speed horizontal decanter centrifuge
2.2 Technical parameters
Rated liquid processing capacity：40m3/h
Rated slag tipping capacity：5t/h
Mix separation point：2μm
Rotating speed：3200rpm
Highest separation factor：2035
Main frame power：37kw
Auxiliary frame power：7.5kw
Pump engine power: 5.5kw (standard deploying 5.5kw long-pole pump, can deploy 11kw screw pump according to the need)
Features of this GLW  355-1250N High speed horizontal decanter centrifuge
a)    Oil gas exploration developer wish to use more clean mud drilling to protect the oil gas layer so as to achieve higher oil gas production.
b)    The using of turbo screw drilling technology put forward higher requirements on the mud cleanness.
c)     More attention will be paid to the disused mud treatment, while treat the disused mud is mainly to separate solid phase from liquid phase as much as possible.

Medium speed centrifuge can separate solid phase granule with the diameter of 5~7μm in low-viscosity mud, as to the thinner granule and high-viscosity mud or the granule in oil based mud, it can not separate them well. So, medium speed centrifuge can hardly meet the new requirements of solid-control system, deploying high speed centrifuge is the development trend in future.
LW355-1250N series of Horizontal high speed centrifuge produced by our company can better meet the above requirements.