Author: admin

GNZYQ1000 mud gas separator is capable of handling 1000~1400gpm drilling fluids. We have 6 units of mud gas separator in stock which are all ready for shipment with painting &　package, welcome to contact with our sales. Except for mud gas separator, we also have flare ignition device in stock, which usually worked together with mud gas separator for oilfield. Mud gas separator is used to separate the harmful gas from the drilling mud, then flare ignition device is used to connect to the gas discharge line of mud gas separator, and burned it , they work together to avoid “kick” situation.

According to base type , the mud gas separator can be divided into :

• Fixed type
• Elevating type

According to the bracket type, it can be divided into horizontal type and vertical type. Most of Chinese mud gas separator is vertical installed, when you need to transport it, you can lay it down , and there is lifting pad hotizontally. MI-SWACO mud gas separator is horizontal type with a skid, it is for simplifies transport, spotting and installation. Unit can lay down during over-the-road transport

Continue reading “Mud gas separator in stock”

GNZS703 shale shaker produced by GN solids control has been widely used in oil & gas drilling. GNZS853 shale shaker is normally used for drilling cuttings treatment.

Below is the photo taken in South America oilfield drilling site. They use GN shale shaker to separate the large solids from the drilling fluids and get clean mud for reuse. Also they user GN shale shaker as a underflow shaker to help the performance of desander cone & desilter cone. 

To know how to operate GN shale shaker is much more important, also the maintenance. Only if you operate and maintain it according to the manual, you will use it same with some famous brand  shale shakers.

1 Angle adjustment

The angle can be adjusted both under running and off condition.When delivered ,the deck is horizontal(0°) 。While operating with the same shaker screen, according to the worksite mud property, and feeding capacity ,by adjusting the deck angle in order to improve the treatment result .When the drilling mud run off, enlarge the deck angle to solve the problem. Angle adjustment range -1°~+5°，rated angle 0°~3°。

2 Pool configuration

A better pool configuration can maximize the screen area and such achieve better result. It is hard to set the deck angle at one time ,it needs the operation personnel adjusting several times according to the flow of the mud .The best pool configuration is when the mud covers the first and second shaker screen.

3 Screen tention

Continue reading “Shale Shaker for Sale”

GN will show a 14 inch bowl decanter centrifuga at OTC, after the show, it will be sold out to South America. To length the service life of decanter centrifuga in drilling fluids separation, proper installation & maintenance is necessary.

At present, GN provide the decanter centrifuga below:

By bowl speed: high speed decanter centrifuga, middle speed decanter centrifuga y VFD decanter centrifuga

By bowl diameter: 14inch bowl, 8.7 inch bowl, 18inch bowl y 22 inch bowl decanter centrifuga

By speed adjustable o no: fixed speed decanter centrifuga y VFD decanter centrifuga

By screw propeller protection method:　coating with tungsten alloy o welding with tungsten carbide tiles

Totally we have GNLW223, GNLW363, GNLW452, GNLW453, GNLW553 series centrifuga. The main components of GN decanter centrifuga are as below:

1 bowl drive motor 2 screw conveyor drive motor 3 gear box 4 screw conveyor 5 bowl 6 hydraulic coupling 7 skid 8 vibration isolator 9 collection box 10 solids discharge chute 11 feed tube 12 fluids discharge churt 13support bracket

Among them, gear box, feed tube and screw conveyor is the most wearable parts, you need regular maintenance on them.

Continue reading “Decanter Centrifuga”

Drill cuttings are separated by shale shaker, decander, desiler, decanter centrifuge, and collected by screw conveyor or vacuum unit , for further separation of vertical cutting dryer & decanter centrifuge.

In an ideal situation, all drill solids are removed from a drilling fluid by solids control equipment on a drilling operation. The two primary sources of solids are chemical additives and formation drill cuttings. Drill cuttings are contaminants that degrade the performance of the drilling fluid. If the drill cuttings are not separated, they will be ground into smaller and smaller particles that become more difficult to remove from the drilling fluid.

Most formation solids can be removed by mechanical means at the surface. Small particles are more difficult to remove and have a greater effect on drilling fluid properties than large particles. The particle size of drilled solids incorporated into drilling fluid can range from 1 to 250 microns (1 micron equals 1/25, 400 of an inch of 1/1000 of a millimetre).

Continue reading “Drill cuttings separation”

Whatever the drilling is, if only there is mud system, you will have mud mixing and agitation issues after a period of drilling.

Mud mixing equipment

GN jet mud mixer is specially used for mud mixing. GN Jet mud mixer is composed of a venturi type hopper and a centrifugal pump, we have 4 models available, GNSL150-45S,GNSL150-35S, GNSL100-25S,GNSL100-25M with 1320gallons/min, 880gpm, 400gpm and 264gpm mixing capacity.

How a venturi hopper work?

The fluid velocity must increase through the constriction to satisfy the equation of continuity, while its pressure must decrease due to conservation of energy: the gain in kinetic energy is balanced by a drop in pressure or a pressure gradient force. An equation for the drop in pressure due to the Venturi effect may be derived from a combination of Bernoulli’s principle and the equation of continuity.
Mud agitation equipments

Mud agitator is mainly used for mud agitation, sometimes for mud mixing. Also in some applications, vacuum degasser also be called a” big mud agitation equipment”.Mud agitator is composed of electric motor and gear box, the popular connection method is direct connection, in some countries, they still use shaft connection mud agitator.

Continue reading “Mud mixing and agitation equipments”

GN has 4 units of poor boy degasser in stock, in addition, we have 9 units of flare ignition device in stock, which is worked together with poor boy degasser as safety equipments in the oilfield drilling.

The poor boy degasser model in stock:

Model	GNZYQ1000G
Main body diameter	1000mm
Capacity	240~320m3/h
Inlet pipe	4″
Mud Output pipe	10″
Gas discharge pipe	8″
Weight	2000kg
Dimensions	2000×2000×5860mm

How poor boy degasser work to be anti-H2S?

( harmful gas , including but not limit to H2S)

1^st way: The main material of the poor boy degasser body is 16Mn(Q345A), which is low alloy, high strength steel.

2^nd way: By 3 layers of Marine Anti-Corrosion Zinc Rich Expoxy Paint:

(1). Sand Blast Treatment before painting.

(2). Two pack Epoxy zinc

(3). Two Pack Epoxy hi-build containing anticorrosive pigmentstwice.

(4). Surface pigmented with high quality light fast  PU pigments

To buy poor boy degasser in stock, welcome to contact GN solids control.

Here share some new photos taken at CIPPE 2013( the largest petroleum show in Asia), which is held in Beijing at New China International Exhibition Center.

We take a lot of new equipments there, mainly divided into 3 sections:

1) 1 set of complete 500gpm trailer mounted mud system) for HDD( horizontal directional drilling)

2)1 set of drilling waste management system( trailer mounted) for drilling cuttings treatment

3)22inch big bowl big volume centrifuge GNLW553G

4) Mini mud cleaner (desander cone only),shaker screens

They include all GN main applications, HDD& CBM, oil & gas drilling solids control & drilling waste management. Generally speaking, the oil show is successful. Most solids control manufactures in China & in USA shared their new developed equipments. For example, trailer mounted mud system, Flocculation unit, Continue reading “GN at CIPPE 2013 Oil Show”

GN has 6 units of flare igniters in stock, they are widely used for oil & gas drilling operations, usually works together with GN own designed mud gas separator. The flare igniters are used for connecting to the gas discharge line of mud gas separator, and fire the dangerous gas from the drilling mud like H2S. GN manufacture the flare igniter according to API &ISO standard, which meet most of the oil industry applications.

flare igniters in stock

The upper part of the flare igniter is stainless steel, and it is designed for rain proof , water proof in the oilfield. The major components for the electrics are from famous brand like Siemens or Schneider. The power of the electric can be directly from industry normal power, or users can charge the battery and take the unit for remote areas application. GN flare igniter is with remote control, and PLC is optional available for less manpower notice for continually and automatically working.

Continue reading “Flare Igniters in Stock”

GN has 6 units of vacu-flo degassers for sale, with electricity 440V/60HZ, 3phase, explosion proof and flame proof. It is well packaged and ready for shipment. If you have requirement on Vacu-flo degassers or vacuum degassers for your drilling mud system, pls contact GN immediately.

Technical specs of Vacu-flo degassers for sale

Model	GNZCQ270
Main diameter	800mm
Capacity	1200gallons/min
Vacuum	0.030~0.050Mpa
Ratio	1.68
Efficiency	≥95%
Motor power	22KW
Vacuum Power	3KW
Rotary speed	870r/min
Dimension	2000×1000×1670mm
Weight	1350kg

Note: You do not need feed pump for GN vacu-flo degasser.

Continue reading “Vacu-flo Degassers For sale”

Mud guns are meant to provide supplemental or primary mixing in mud tanks depending on the number being used and the pit size. They are best used in tank corners to keep solids from settling and a mud agitator is placed in the tank center.

How to operate the mud gun?

A. Safty information

TURN OFF. LOCK OUT, and TAG OUT the electrical power supply to the pumps feeding the mud guns before servicing.

Inspect the unit regularly, and replace damaged or worn components only with parts supplied by the original equipment manufacturer.

Before entering a mud tank for any reason, the mud agitators should be locked out and tagged out.

B. General maintenance

1. Grease the swivel once a week. Add (2) shots of a multipurpose NLGI no 2 grease.

2. Visually inspect the mud gun assembly for any leaks, loose fittings once a week. Repair as required.

3. Inspect mud gun jet nozzle for excessive wear. The nozzle has a 5/8” bore when new. The nozzle should be changed when the bore is 7/8” or higher. This should be done once a month.

Once installation is complete, the unit can be started by turning the feed pump on. The direction of discharge may be modified to suit the operators requirements by rotating the swivel.

How to calculate the mud gun qty on a mud tank？

Continue reading “How to operate a Mud gun?”