Mud Solids Control Equipment

Why we should have drill slurry storaged? Mainly it is because of the reasons below:

(1)   Requirement for the carriage and storage of mud on mobile drilling units has increased over the years, it is not convenient to process the drilling mud at the platform, you have to collect the used drill slurry and carry it to drilling fluids plant for process, then recycle the clean drill slurry and disposal the useless cuttings, so that it will not influence the environment.

Drill Slurry Storage

(2)   Clean drill slurry should be storaged for use, for drilling , for mixing , for lubricate the drill bit.

(3)   Useless drill cuttings should be collected and storage, then carried to drilling waste management system for process.

GN solids control manufacture drill slurry storage tank for various application, with necessary mud agitators, mud gun, centrifugal pump and mixing hopper. We can produce mud storage tank together with solids control system or separately. Compared with shaker tank and intermediate tank, the pipeline of storage tank is much simple, if required by the clients, we will divide it into several compartment by clapboard. Sometimes mud ditch is installed on each compartment. Handrails, stairs, cleaning gate, valves are included, but walkways are not included. There is flexible hose connected 2 tanks.

Continue reading »

written by GN solids Control \\ tags: centrifugal pump, Drill Slurry Storage, drilling mud, drilling waste management, mixing hopper, mud agitator, mud gun, shaker tank, solids control system, storage tank

GN solids control produced various kinds of mud tanks for oilfield drilling and water well drilling, including swab tank, storage tank, fuel tank, water tank, mixing tank, suction tank, pill tank, trip tank, mixing tank, intermediate tank, shaker tank etc.

General features of GN mud tanks

oilfield swab tank

1 Customized dimension

2. Sand Blast Treatment before painting.                                                                                            

 3. Two pack Epoxy zinc(Japan Kansai & Cosco brand)                                                                                    

4. Two Pack Epoxy hi-build containing anticorrosive pigmentstwice.                       

5. Surface pigmented with high quality light fast PU pigments

6 Stainless steel material tank available

7 Skid Mounted 3 Runner Oilfield Design

8 Proper mud agitator and mud guns are available

9 Mud tank accessories included

Oilfield Swab tank

Also called test tank, each plumbed for separate discharge to vacuum truck or water tank. Complete with minimum 32 ” Poor-Boy Degasser with proper vent, fluid leg and inspection hatch. Usually we will provide a complete sets of measurement tools, including Mud Balance, Plastic Marsh Funnel Viscometer and Plastic Measuring Cup and Stopwatch.

Oilfield trip tank

A small mud tank with a capacity of 10 to 15 barrels, usually with 1-barrel or h-barrel divisions, used to ascertain the amount of mud necessary to keep the wellbore full with the exact amount of mud that is displaced by drill pipe. When the bit comes out of the hole, a volume of mud equal to that which the drill pipe occupied while in the hole must be pumped into the hole to replace the pipe. when the bit goes back in the hole, the drill pipe displaces a certain amount of mud, and a trip tank can be used again to keep track of this volume.

Continue reading »

written by GN solids Control \\ tags: intermediate tank, mud tank, oilfield drilling, pill tank, shaker tank, storage tank, suction tank, swab tank, trip tank, water tank

We make shearing jet system for bentonite polymers and other powder additives mixing.We links the shearing jet system to the mud mixing tank for assisting in achieving the properties needed from drilling mud such as viscosity for hole cleaning, water loss control and filter cake build up.

Jet Shearing system

The shearing jet system is a skid mounted system,which a centrifugal pump and mixing hopper are installed.On weighted mud applications, the ability to handle Barite during potential blow-out applications is even more important. The importance of properly applied shear energy and dispersion has lead to the instant success of GN Solids Control shearing and mixing system, model:SLH Jet mud mixer

In the GN Jet shearing system, mud passing through the hopper venturi is directed to pass through specially designed jet orifices to impart additional shear energy.
Continue reading »

written by GN solids Control \\ tags: jet system, mud system, shear pump, storage tank