Author: admin

Last week, the oil -based mud diamond dumpling machine produced by GN Solids Control was sold to a mud company abroad. The following specifically introduced:

1. GN solids Control Drilling cutting drying machine

Drilling cutting dryer by GN Solids Control is mainly used to treat oil -based rock chips and synthetic base rock chips. After the drilling rock scrap dried machine is treated, the oil content on the rock chips can be controlled below 5%. The model of this supply is GNCD930G, which is designed for integrated module, including containers, screw conveyors, centrifugal pumps, hanging ups and hanging devices.

Core equipment drilling vertical cutting dryer machines mainly include sieve baskets and rotors. These two main components run in the same part at different speeds. Solid particles that are more than 250 microns can be separated from rock chips. The rock crumbs produced by GN Solids Control have different sized sieve baskets of 3, including 250 microns, 350 microns and 500 microns. There is a difference between the speed between the rotor scraper and the sieve basket. The remaining solids that remain on the inside of the screen basket are continuously scraped off by the scraper and transported to the bottom of the sieve basket. The scum discharge port is collected and the discharge machine is extended to achieve the drying of drilling.

 

GN Solids Control has provided hundreds of drill chip drilling machines for global companies such as Baker and Shell.

GN Decanter Centrifuge

Decanter centrifugal machine is one of the key equipment for drilling mud solid -phase control and drilling waste treatment. There are many rotating sizes produced by GN Solids Control to choose from, including 9 -inch, 14 -inch, 18 -inch, 22 -inch, and 30 inches. The drum material is made of two -way stainless steel SS2205 or SS32304. It has better performance. The abrasion -resistant cover of the residue port is a tungsten carbide hard alloy cover, which is extremely abrasion -resistant and is not easy. At the same time, the feeding device is protected by replaceable wear -resistant alloy tablets, with long service life and easy maintenance.

GN Solids Control is a 14-inch horizontal centrifugal machine, model GNLW363D-VFD, the same integrated design, including containers, liquid pumps, and spiral conveyors.

The integrated design of the two modules can meet fast installation and transportation, and can also meet the use of low -temperature areas in winter.

If you have equipment requirements or solution consultation in this area, welcome to call GN Solids Control

GN Solids Control has been committed to the design and equipment manufacturing of solid -liquid separation processing system for many years. Since its establishment, GN Solids Control has reached a long -term cooperative relationship with many well -known drilling companies, providing various solid -liquid separation processing equipment for customers each year, like decanter centrifuge/ shale shaker/ mud cleaner. With the advancement of the times, there are more and more methods of drilling mud recovery, and more and more effective. The GN Solids Control has followed the trend. 20-30%Recovery, while reducing drilling waste, saving new mud costs and the cost of transportation processing of waste.

By using it, the client may not need use vertical cutting dryer or decanter centrifuge for further waste treatment.

Last week, the VIST triple negative pressure shale shaker of the GN Solids Control was sold to a drilling company in China. The main working principle was to install a negative pressure suction cup under the last screen of the shaker. The frequency negative voltage pumping, realizing the dual separation of vibration and negative pressure, thereby increasing the recovery of drilling fluids and reducing the liquid content of the excreted drill chips.

 

The main characteristics are as follows:

1. Triple negative pressure shale shaker is fixed by a three negative voltage shale shaker on one front seat to meet the fast installation and handling needs. At the same time, it does not require an extra area to meet the requirements of drilling space.

2. GN VIST is formed by air -driven negative pressure and can be used in any explosion -proof environment.

3. Multi -selective, the negative pressure generator can control the three vibration sieves at the same time, or it can also control one. Customers can choose whether to use them according to on -site needs.

4. It can be changed to a negative voltage shale shaker for customers who already have conventional shale shaker, which are convenient and fast installation.

5. Use the GNZS595J model to shale shaker with 5 pcs screen nets. The processing volume has been significantly improved. Drill mud has been treated for a longer period of vibration on the mesh surface, and the rock chips are more dry.

6. Negative pressure shale shaker installation anti -splashing device to avoid drilling mud splashing, protect the site cleaning, and optimize the working environment of the operator.

If you have this need, please call GN Solids Control.

As a well -known domestic solid control equipment manufacturer, Gn Solids Control has passed multiple certifications such as API, HSE, CE, ISO 9001, and has more than 40 patents. So far, GN Solids Control has provided solid control equipment for more than 70 countries and regions, such as vibration sieves, mud removal, sand device, centrifugal pump, diving pump, vacuum pump, etc.

GN Solids Control has mature technical technology and excellent technical teams. It invested a lot of time and energy every year and is committed to research and development. delivery.

 

For this mute solid vacuum pump, when designing the GN Solids Control engineer, it placed it in the mute shell to cover the entire solid vacuum pump. The GNSP40B vacuum pump in the shell is perfectly combined with the mute device, which will not cause unnecessary movement to ensure the stability of the vacuum pump inhalation and exclusion process, reduce unnecessary noise generation, and the silent device can further weaken the sound of the vacuum pump when working normally. As a result, noise decibel control is controlled within the customer’s requirements. Its unique structural design enables it to operate in a difficult environment. The maintenance rate is low, and it can transport solids, liquids or solid -liquid mixtures and high -gravity materials with good liquidity. Its working principle is that the efficient Venturi device generates up to 25 -inch HG vacuum in the case of strong airflow and sucks materials and pure gas moving equipment. The mute solid vacuum pump provided this time contributed sweaty to the shield sludge.

GN Solids Control has delivered various standards and customized solid control equipment for customers abroad for many years, such as shale shaker/centrifuge/mud tank, which has obtained many high -quality feedback from customers. If you are about equipment requirements or plan consultation on this area, please contact

GN Solids Control is a professional drilling mud treatment equipment manufacturer. The crown can have two series of mud processing systems. The D series is a economy mud treatment system. The B series is a high -profile mud treatment system. The D series products are mainly used for the purification and recycling of mud. It does not have the function of storing mud and mixed mud. It requires additional configuration of slurry tanks and mixture equipment. B series products integrate mud purification and recycling, mud storage, and mud mixing functions, and are divided into multi -level purification treatment, which can meet the needs of high -end and large and medium -sized rigs. This article mainly introduces high -profile mud treatment systems. The main characteristics are as follows:

 

The standardized and styling design of many years of experience is comprehensive. The product has strong applicability, reasonable structure, and stable operation. Multifunctional integrated design can meet the functions of mud cleaning, mixed mud, storage, etc. Self -cleaning design, reducing the tank cleaning work, compact structure and strong separation ability. All the electrical control systems use explosion -proof, dustproof, and waterproof crown energy control boxes, and use Siemens or Schneid Electric Electric Components. The guardrail adopts a foldable design to facilitate disassembly transportation.

With a straight line shale shaker, the shale shaker can reach 7.5g, which can be adjusted. The bottom frame of the stainless steel sieve box, combined with a compressed sieve box seal protection, has a long service life. The vibration motor uses an international brand OLI or Martin, USA. The vibration spring is a rubber -wrapped type, extending the service life and reducing noise. Wedding sieve network installation to meet the requirements of fast disassembly.

The all -in -one machine uses a stuck polyurethane rotor, which has a long service life and easy to repair. 10-inch sandwiches, separation particle size 40-60um, 4 inches to remove mud rotor, separate particle size 20-40um, to meet the requirements of duplicate mud.

The centrifugal pumps in the remaining supporting devices are all mechanically sealed and have a long service life. The mixer adopts a direct Flat -connected formula, the FAG brand deceleration machine bearing, the structure is compact and runs stable. The mud gun nozzle and the firing dragon nozzle are made of wear -resistant polyurethane material. The paint adopts the Japanese brand epoxy zinc -rich ocean heavy anticorrosive paint.

The GN high -profile mud recovery system can be designed to be designed as a pilomy type, hydraulic lifting type, and a fast movement requirements for car to meet different operating conditions. GN Solids Control is the first domestic solid control equipment manufacturing company to launch a hydraulic lifting mud recovery system, which is exported to Australia, the Middle East, Russia and other regions.

If you have the needs or problems of mud purification system, you need to consult, welcome to contact GN solids Control

This week, Gn Solids Control has completed the production and manufacturing of two sets of solid vacuum pumps. The GN SOLIDS Control vacuum pump is a purely aerodynamic conveyor pump. The two sets of vacuum pump models provided for African customers this time are GNSP-10B and GNSP-40B.

As we all know, the waste at the oil drilling site is usually high and has a certain viscosity. For example, the drilling cuttings discharged from  shale shaker are difficult to transport the general transport pump, but the solid particles only need to be less than 75 mm and have a certain liquidity. GN The Solids Control vacuum pump can complete the transportation task, and the transport distance can reach up to 1,000 meters.

 

Among the two vacuum pumps provided by African customers, the vacuum pump of the model GNSP-40B is used for the conveying of on-site drilling waste, which avoids the drop of waste caused by using other devices such as excavators and other wastes to protect the on-site environment. At the same time, hazardous disclosure may occur at the time of drilling. It needs to be cleaned in time. The routine manual cleanup speed is slow, and the on -site operation is delayed. However, using the model GNSP-10B vacuum pump with GN unique pulp, it can be used as an industrial vacuum cleaner to quickly clean up the scene. This vacuum pump is equipped with wheels underneath.

The GN SOLIDS Control vacuum pump can also be used for the cleaning of mud tanks. During the drilling process, the type of mud is needed to clean the mud can. The waste mud after washing the tank can use the vacuum pump for suction and clean up to improve efficiency. When the sludge pit is processed, the conventional transportation equipment is difficult to transport the sludge. It can be transported by the crown can be used to solve the incurable diseases.

The conventional vacuum pump is made of carbon steel. If you encounter special materials, GN Solids Control can also provide a vacuum pump for stainless steel.

GN Solids Control has delivered multiple sets of solid vacuum pumps for domestic and foreign customers for many years, and has obtained high -quality feedback from customers. If you are about equipment requirements or plan consultation on this area, you are welcome to call GN solid control.

Last week, GN Solids Control provided three large oil drill solid control equipment for South American customers, mainly including:

1. Drilling liquid shale shaker

GN Solids Control Drilling liquid vibration screening uses Italian OLI or Martin Motor, and electrical components use Siemens Schneider brand. The negative load design, the overall heat treatment of the sieve box, the vibration strength can reach 8.0g, which can meet the use of various working conditions. It is mainly used for solid particles with a first -level screening and is separated from 100um. The vibration screen model is GNZS594J.

2. Mud Cleaners

GN Solids Control Mud cleaners are a tight processing device. It is equipped with a sand removal and mud device on the vibration screen to form a compact integrated module, saving a lot of space for transportation. The mud cleaning device provided to customers is equipped with a 10-inch sand removal and a 4-inch mud removal flow. The sand removal can be separated from 40-60um solid particles. The above solid particles. The supply model is GNZJ594J-3S16N.

 

3, centrifugal pump

GN Solids Control Sand Pump is mainly used to transport drilling mud, which can be used as a slurry pump for sand removal, mud device, and centrifuge. Pump is used. This sand pump is used as a solution pump for mud device and sand removal.

4. Decanter centrifuge

Drilling solution is widely used in the proportion control of drilling fluids and heavy crystal recycling. The price of drilling fluid is very expensive. Because it usually needs to add chemicals, it can be re -used after it has a certain proportion and viscosity. Therefore, it is important to recover more drilling fluids. GN Solids Control Drilling solution The centrifuge of the drilling solution is processed under high speed and high gravity, and the drilling solution is separated to recover more drilling fluids.

5. Screw paste pump

GN Solids Control In the selection of the slurry pump of the horizontal snail centrifuge, the screw pump is generally selected. Because the screw pump can control the flow of liquid supply and can record the amount of liquid supply. The supply screw pump model is GNG30-075C and the processing capacity is 0-30m³/h. It can be adjusted according to customer needs. At the same time, Guan can also provide other models of screw pumps for customers to choose.

GN Solids Control has been committed to providing customers with cost -effective solutions. If you have any needs, you can contact us at any time.

GN Solids Control is a professional solid control equipment manufacturer. After more than 10 years of continuous research and development and innovation, GN Solids Control has established overseas branches in the United States and Russia. The GN Solids Control device has now been exported to many countries and regions around the world, and has been accepted and recognized by hundreds of companies around the world.

This week, GN Solids Control provided a batch of mud device, sand removal and vacuum air device for a well -known Chinese entering company. Its main model and parameters are as follows:

1. GNZJ752J-1S

 

The GN Solids Control GNZJ752J-1S sand removal has a small structure and affordable characteristics. It uses GNZJ752J mini-type bottom flow sieve with a screen area of 1.4 square meters and 1 “sand removal device. It can separate solid particles with more than 60um. It is mainly used in small oil drilling machines, coalbed methane drilling, horizontal directional rig and wells.

2. Muddy removal GNZJ752J-8N

Like the GN Solids Control sand removal, the GNZJ752J mini-type bottom flow is also used, but it is equipped with hydro cyclone, which can separate solid particles above 20-40um. The field is basically the same. As a purification equipment at the back end of the sand removal, the purification effect of mud is guaranteed.

3. Vaccum Degasser Gnzs270B

GN Solids Control Vacuum Vacuum removal is usually installed after the vibration sieve, which can effectively separate the harmful gases in drilling mud, maintain the proportion of mud, and protect the sand pump and mud pump to improve the effect of the subsequent equipment. The GN Solids Control Vacuum removal is used by autonomous pulp, and there is no need to be equipped with a paste pump. At the same time, GN Solids Control can also provide centrifugal gasifiers, which is small compared to vacuum aircraft and occupy small space.

GN Solids Control can be equipped with a complete set of solid control equipment, including shale shaker, sand removal, mud device, centrifugal pump, vacuum removal, centrifugal machine, mud jar, etc. If you have solid control requirements or solution design, You are welcome to call GN Solids Control.

GN solid control company is a professional solid -liquid separation equipment manufacturer. In the oil solid control industry, it can be equipped with a complete set of solid control treatment equipment according to customer needs. In the HDD industry, GN solid control can provide standard mud purification equipment, such as GNMS-200D, GNMS-500D, GNMS-1000D, can also customize exclusive mud purification devices according to the different needs of customers. Last week, GN Control provided four sets of mud purification devices for a Australian customers, mainly as follows:

 

GNMS-200D mud purification device

The shale shaker processing volume is 200GPM, and the separation particle size is 25um. Select 4 4 -inch cyclone, use 100%high -quality polyurethane, and long service life. The bottom flow screen is GNZS753 double -layer shale shaker, with an upper screen area of 0.875㎡, and the underlying screen area is 1.35㎡. the vibration motor uses an international brand Italian OLI or Martin. The bottom frame of the sieve box is made of stainless steel, and the vibration strength is ≤7.1g, which can be adjusted. In addition to the mud supply centrifugal pump model GNSB4X3C-11J, it uses mechanical sealing and has a long service life for easy maintenance. It can swap accessories with the international standard pump. There is a mud recovery tank at the bottom. The overall design is small, covering a small area, the transportation size is 3135mm*1920mm*2521mm, and the total weight of the system is 3012kg, which is convenient for transportation. The electrical control cabinet uses the GN brand to prevent explosion -proof rain and dust. Electric components use Siemens or Schneid components. Safety standards for the aisle guardrails and electrical equipment meet Australian requirements.

If you have problems or needs for mud purification devices, welcome contact GN solids control.

Last week, GN Solids Control provided European customers with three sets of dual -layer straight -line drilling fluid Shale Shaker and a set of mud cleaners. With the development and technology innovation of GN Solids Control, the latest version of Shale Shaker has excellent working performance and satisfactory product quality.

The double -layer straight -line drilling solution produced by GN Solids Control Shale Shaker has 6 piece screen, 3 screen on the upper and lower layers, the upper area is 2.0 square meters, the lower area is 2.6㎡, the total area is 4.6㎡.

During the double -layer Shale Shaker works, the upper screen can separate solid particles with larger diameter, and the number of sieve nets is relatively low; the underlying screen network can separate the solid particles with less diameter, and the number of sieve nets is relatively high. We can replace the screen separation requirements according to the actual needs of the site to meet the on -site separation requirements.

 

This European customer used to use US brand double -layer drilling fluid Shale Shaker. The client drilling machine supporting solid control system was updated and upgraded. He chose to use the GN Solids Control double -layer straight line Shale Shaker to replace the previous Shale Shaker. The reason is as follows:

1. Double -layer Shale Shaker supporting mechanical screening network fast pressing device, which can easily and quickly disassemble the screen, and the skin is durable. Compared with the traditional method, a total of at least 30%of the replacement screen time is shortened.

2. The screening area is large, and the straight line trajectory of high excitement is used. The excitement can reach 7.2G, which can meet the processing requirements of the drilling fluid when the large land rig and marine rigs are quickly drilled into the public.

GN Shale Shaker has comprehensively judged from the aspects of quality, performance and price, and has a very high cost performance. Therefore, European customers chose GN Solids Control.

GN Solids Control produces and sells more than 300 Shale Shaker each year. It is also exported to other solid control equipment such as residential snail centrifugal machines, centrifugal pumps, and mud agitator. If you have this need, please contact GN Solids Control.

   Recently, GN Solids Control has completed a batch of drilling liquid shale shaker and mud cleaners that are satisfied with three petroleum drill drilling drilling mud. With the upgrade of GN  solids control technology, the product launched to customers this time is the new -generation J version solid control shale shaker. The upgraded J version of the shale shaker is greatly improved in the performance, the convenience of operation, and the durability, which can better meet the long -term stable use needs of drilling mud solid -control field operations.

       The solid control shale shaker is one of the core equipment of drilling mud solid control. I believe everyone is no stranger to shale shaker, because it is essential in oil drilling. When the drilling fluid is returned with a large amount of rock chips through the mud distributor, the first device entered is shale shaker. Its main function is to make preliminary coarse sieves on drilling mud, which mainly separate large granules. The number of shale shaker screen can be from the API 10 to the API 325, which can be selected according to different work choices, so that the shale shaker can be separated from the particle size range and meet the different requirements of customers for different scenes. GN SOLIDS Control sells more than 200 shale shakers each year, with mature production technology and excellent technical teams. Today, GN Solids Control’s technical team has developed a new generation of solid control shale shakers. Compared with the previous version of the shale shaker, the J version solid The main advantage of the control shale shaker is as follows:

 

1. The bottom frame adhesive adopts a new generation of patented technology, with good abrasion resistance, long service life, and convenient replacement.

2. It can facilitate the selection of drilling liquid shale shaker and mud cleaning device.

3. It can facilitate the customer’s shale shaker and installation of the negative pressure device, and convert it into a negative pressure shale shaker.

4. It can be more convenient to adjust the angle of the shale shaker box.

5. Shale shaker stainless steel bottom frame support device, which can better meet long -term marine drilling anticorrosion.

6. High -intensity imported well -known brand vibration spring, good performance, long service life.

     GN Solids Control is a professional solid control and waste processing equipment manufacturer. The equipment produced not only occupied a place in the domestic market, but also exported to more than 70 countries abroad. Its main products include shale shaker, decanter centrifuge, cleaning device, centrifugal pump, agitator, etc. The industry is developing, and the times have improved, and GN Solids Control has not stopped. In terms of quality, we strive to use users with peace of mind; in the intersection, we will actively cooperate with the project requirements; in terms of service, we will do our best to our customers; in terms of price, we will let customers get the most valuable products.