Author: admin

Recently, GN Solids Control provided a set of oil drilling mud control systems for Indian customers, including double-deck vibrating screens, vacuum degassers, desilters, centrifuges, slurry pumps and mud tanks.

1. Double-deck shale shaker

Linear motion track, using Oli motor, screen box can be adjusted simultaneously, screen box angle adjustment can be performed without stopping. Different mesh screens are used on the upper and lower decks, separation is more precise, processing capacity is large, and it is widely used in large-scale oil and gas drilling mud control systems.

2. Vacuum degasser

GN Solids Control’s vacuum degasser comes in three models, including GNZCQ240B, processing capacity 240m³/h; GNZCQ270B, processing capacity 270m³/h; GNZCQ360B, processing capacity 360m³/h, to meet the requirements of different processing capacities. The vacuum degasser is mainly used to separate small bubbles in the drilling mud, and then sent to the desilter or desander. A vacuum degasser designed to meet the requirements for use on offshore platforms in China is also available.

3. Desilter

The desilter is mainly composed of two 10-inch desilter cyclones, which can separate solid particles larger than 40-60 µm.

 

4. Desander

The desander is mainly composed of 12 10-inch desander cyclones, which can separate solid particles larger than 20-40 µm.

5. Centrifuge

GN Solids Control drilling fluid centrifuges come in multiple sizes to choose from, including 14 inches, 18 inches and 22 inches. GN Solids Control drilling fluid centrifuges are designed and manufactured by API-certified factory, and are widely used worldwide. The GNLW363D horizontal screw centrifuge provided is one of the best-selling centrifuges in GN, and has sold more than units. Conventional mud control systems are equipped with two centrifuges, a medium-speed centrifuge and a high-speed centrifuge, while GN Solids Control’s GNLW363D centrifuge is a typical high-speed centrifuge with good treatment effect and economic benefits, and is popular with customers.

6. Centrifugal pump

 GN Solids Control centrifugal pump components can be replaced with Mishen sand pump components. To extend the service life of the centrifugal sand pump, GN Solids Control centrifugal pump uses nodular cast iron alloy as the pump housing, which has high wear resistance. The impeller of the centrifugal sand pump also uses this material, and high-quality mechanical seals are used to prevent leakage of the centrifugal pump.

Recently, GN Solids Control solid vacuum pump and vacuum degasser passed the factory’s strict inspection and were sold to Chinese drilling companies. The specific models of these equipment are vacuum pump GNSP-40B and degasser GNZS270B. The solid vacuum pump is used as a mud transfer equipment. The vacuum degasser is used as the secondary stage of mud control to remove hydrogen sulfide from the mud. The following is mainly about the advantages of GN Solids Control vacuum degasser.

GNZCQ series drilling fluid vacuum degasser is usually installed after the shaker, which can effectively separate harmful gases existing in the drilling mud, maintain the mud specific gravity, and protect the sand pump and mud pump to improve the processing effect of subsequent equipment. The GNZCQ series vacuum Degasser adopts self-priming mud suction method without additional mud feed pump. The GNZCQ series vacuum Degasser can also play the role of a large mixer to prevent the drilling mud from sedimentation.

 

GN Solids Control vacuum degasser also has the following characteristics:

1. The vacuum pump sucks the mud into the vacuum tank and uses it to suck the gas out of the vacuum tank. The vacuum pump plays two different roles here. 2. The water ring vacuum pump always operates in isothermal state, suitable for flammable and explosive gas suction, with reliable safety performance. 3. The mud is injected through the rotor window at high speed to break the bubbles in the mud completely, resulting in good degassing effect. 4. The main motor is offset, the machine center of gravity is reduced. 5. Belt drive is adopted to avoid the complication of the gearbox. 6. The application of air-water separator does not cause water and gas to be discharged simultaneously, keeping the exhaust pipe unobstructed. In addition, water can be recycled to the vacuum pump to save water. 7. The suction pipe is inserted into the mud tank, and when the mud is free of gas invasion, it can be used as a high-power mixer.

GN Solids Control‘s vacuum degasser also has the following characteristics:

1. The vacuum pump sucks the mud into the vacuum tank and uses it to suck the gas out of the vacuum tank. The vacuum pump plays two different roles here. 2. The vacuum pump always operates in isothermal state, suitable for flammable and explosive gas suction, with reliable safety performance. 3. The mud is injected through the rotor window at high speed to break the bubbles in the mud completely, resulting in good degassing effect. 4. The main motor is offset, the machine center of gravity is reduced. 5. Belt drive is adopted to avoid the complication of the gearbox. 6. The application of air-water separator does not cause water and gas to be discharged simultaneously, keeping the exhaust pipe unobstructed. In addition, water can be recycled to the vacuum pump to save water. 7. The suction pipe is inserted into the mud tank, and when the mud is free of gas invasion, it can be used as a high-power mixer.

In addition to the equipment described above, GN Solids Control also produces a complete set of oil drilling mud control systems, trenchless and coal bed methane drilling mud recovery systems, pile driving and shield tunneling mud purification systems, drilling waste treatment systems, industrial environmental mining and other solid-liquid separation systems.

GN Solids Control is a professional mud processing equipment manufacturer. It has been committed to providing customers with high-quality mud purification solutions for many years. Recently, our company has successfully customized a set of GNMS-1000D mud mud treatment equipment for the top pipe customers in Singapore. And customized a set of GNMS-500D mud purification device for South Africa’s level orientation.

1. GNMS-1000D mud system

The GNMS-1000D mud system belongs to the GN Solids Control independently developed and produced mud treatment system. It is mainly used in mud purification and recycling in non-excavation industries. It is not equipped with slurry and mixed mud. The demand for mixed mud needs to be equipped with mud jars and shooting slurry devices alone. The GNMS-1000D mud processing system has a processing amount of 240m³/h. This system is equipped with a GNZY705E-Y2S mud purification all-in-one. The sand removal uses 2 10-inch desander, which can effectively extend the service life. The system paste pump uses a 45kW GN Solids Control Centrifugal Pump GNSB6X5C-13J.

 

2. GNMS-500D mud purification system

The GNMS-500D mud purification system also belongs to the GN D series economy mud treatment system. It does not have the function of mixed mud and storage mud, and the relatively small processing volume is 120m³/h. The machine uses a 10-inch polyurethane rotor, and the slurry pump uses a 30kW GNSB5X4C-13J Centrifugal Pump.

In addition to the D series economy mud treatment system, GN Solids Control can also provide customers with B series high -style mud purification systems. The B series high -profile mud purification system integrates mud purification and recycling, storage and mud mixing functions, and mud mixing functions. It can increase multi -level purification treatment equipment to meet the needs of high -end and medium and large rigs. If you have relevant needs, please contact us.

Last week, GN Solids Control provided a complete mud purification equipment for a New Zealand customer for vacuum excavation mud purification treatment.

The equipment mainly includes mine screen separation device, high-frequency fine vibration screen, desilter , decanter centrifuge, among which:

1. Mining vibration screen

This device is a vibration screen, which mainly separates the large diameter solid particles and has a large processing amount. Because the large diameter solid particles are more wear out of the sieve network, the flexible polyurethane sieve net is used. The sieve of this material has high wear resistance, which improves the continuous operation capacity and work efficiency of the equipment, thereby increasing economic benefits Essence

 

2. Shale shaker

This device is a fine separation unit, which mainly separates solid particles above 100um. The processing volume is less than the mine equipment, but the screening effect is more. The imported vibration motor is used like a mine sieve to ensure the service life. After the overall heat treatment of the sieve box, the torment strength can reach 8.0g. The bottom frame is made of stainless steel, which is strongly corrosive. It can meet the angle of non -stop operation to adjust the angle of the sieve box, and the operation is more stable.

3. Desilter device

The liquid phase after high-frequency fine screen treatment enters the desilter again, and the solid particles larger than 20-40um can be removed by the desilter. The cyclone of the desilter is made of polyurethane material, which has higher wear resistance.

4. Decanter centrifuge

GN Solids Control centrifuge can separate solid particles larger than 2-5 µm. The centrifugal separators are necessary because the slurry after desliming treatment does not meet the criteria for recycling. Centrifugal separators reduce the specific gravity of the slurry to allow for reuse. The decanter centrifugal are fabricated with bi-directional stainless steel centrifugal casting, which is superior to 304 and 316 materials. The wear-resistant head of the waste discharge port uses a special tungsten carbide hard alloy bushing, which provides excellent wear resistance. The separators are dynamically balanced three times – at medium speed, high speed, and overall – to ensure stable operation under high-speed conditions. Producing products of inferior quality is equivalent to creating waste. GN Solids Control has always adhered to the principles of safety first and top quality, which has allowed it to develop rapidly within the industry.

If you have any solid-liquid separation equipment needs, please contact GN Solids Control.

Last week, GN Solids Control completed a set of 2M3 /H oil sludge treatment systems for domestic market customers. As a professional mud pre -processing equipment manufacturer, GN Solids Control has provided high -quality products and services to global customers over the years.

The following is the main component of the GN Solids Control pneumatic processing system:

1. Premix heating module

The GN Solids Control pre -hybrid heating device is the preferred process for processing high density and large viscosity sludge, which is not easy to transport because it is not diluted. GN Solids Control By premature and filtering the mud in the raw material pool, the mud can be removed smoothly. A chemical plus device is connected to this device, which is used to add emulsion and other potential agents.

2. Separation module

The separation equipment is a three -phase processing device that can separate oil -containing sludge into oil, water and mud. The pre -processing sludge is pumped into the GNZS752J pneumatic shale shaker, which effectively removes larger particles in the sludge. Usually solids greater than 100 microns can be removed by vibration screen. The wastewater discharged from the clay vibration sieve enters the 220mm-to-stock diameter and the decanter centrifuge GNLW224ET is further separated from solid solid fluid. It can remove solids above 2-5 microns and thinner particles from the liquid. In order to make the oil and water separation more thoroughly, the GN Solids Control provides a 3-phase disc separator GNSD-40 after the two-phase snail is centrifugal.

 

The 2m3 /h pneumatic processing system is a standard processing device, which makes it easy to move between different places. GN SOLIDS Control also offers a larger standard processing device of 5M3 /H and 15M3 /H for continuous processing of mud. Usually according to on -site usage, GN Solids Control will customize the sludge processing system so that customers can get an economic effective solution.

GN Solids Control has been providing drilling solids control equipment and waste conveying equipment to global customers for many years. Last week, GN Solids Control provided 8 screw conveyors to the drilling company.

The screw conveyor supplied this time has the following functions:

1. The cover plate on the top of the spiral is made of steel grating, which is detachable. At the same time, one end is a hinge and the other end is a locking bolt. The cover plate is opened conveniently and quickly.

2. Equipped with a pull switch, when someone opens the cover, the screw will automatically stop. When the pull switch is not reset, the screw cannot be restarted, which has high safety.

3. In order to further improve the safety of the equipment, the electric control box is equipped with an emergency stop switch to realize emergency shutdown.

 

4. When the screw is started, the sound and light alarm on the electric control box will alarm to remind the surrounding workers that the screw is about to start, and the sound and light alarm time can be adjusted. When the alarm time is up, the spiral will start automatically.

5. There is an obvious safety reminder mark on the spiral, which meets the HSE requirements. At the same time, the electric control of the motor and the spiral equipment are grounded.

6. Spraying system, along both sides of the entire spiral, there are clean water flushing pipelines, with nozzles and valves, so that the spiral can be rinsed without opening the spiral cover to prevent the spiral from clogging.

7. The cover plate of the screw conveyor is designed to prevent collapse to prevent accidents caused by operators stepping on the cover plate by mistake.

The screw conveyor can directly collect the solid waste separated by shales shaker, desilter, desander, decanter centrifuge and other equipment at the drilling site, and transport it to the location where the customer needs to be delivered. It plays an important role in the project that the mud does not fall to the ground.

If you need solid control equipment or waste conveying equipment, please call GN Solids Control

GN Solid Control, a company specializing in oil sludge treatment, has successfully provided a complete set of oil sludge treatment systems to an environmental client in the Middle East. This system is primarily used for treating oil sludge from drilling platforms, refineries, and the bottoms of oil tanks. Designed specifically for high viscosity and high solids content oil sludge, the GN oil sludge treatment system produces three main products: oil, water, and solids.

Recently, GN Solid Control Company delivered a complete oil sludge treatment system to their environmental client in the Middle East. The system includes the following main components:

Pumping Module:

The core equipment in this module is a vacuum pump. GN’s vacuum pump is an air-powered pneumatic pump. The module includes an air compressor that generates compressed air to power the vacuum pump. The vacuum pump is capable of transporting various materials such as drilling waste, industrial slurry, chemical powders, construction aggregates, oil sludge, and kitchen waste. Its strong conveying capacity makes it excellent for oil sludge transportation, effectively completing the conveying task by delivering the oil sludge to the preliminary screening module.

Preliminary separation Module:

The main equipment in this module is a mining screen. After the materials are crushed by a crusher, they pass through the mining screen for particle separation, separating large solid particles. The separated materials are then transported to the heating and mixing module. GN Solid Control has independently developed and produced various models of mining screens with excellent separation efficiency and long service life.

Heating and Mixing Module:

Due to the high solids content, high viscosity, and poor flowability of the oil sludge material that the client needs to treat, the GN oil sludge treatment system is equipped with a heating and mixing module. The mixing tank is equipped with an agitator to prevent oil sludge precipitation. The mixing tank also has a heating function to improve the fluidity of the material through agitation and heating, facilitating pumping. This module is placed in a 20-foot container.

 

Fine material separation Module:

The system utilizes the GN GNZS706 dual-deck shale shaker. The upper deck uses a lower mesh number screen, while the lower deck uses a higher API number screen. Multiple screening processes with a large screening area and extended time result in better separation conditions for the decanter centrifuge. The shale shaker uses GN Solid Control’s own production of shaker screen, which comply with the API RP 13C standard.

Decanter Centrifuge Module:

After the oil sludge is screened by the shale shaker, it is pumped into the GN decanter centrifuge for two-phase separation. The separated solid phase has an oil content of ≤5%, while the liquid phase consists mainly of oil and water. The solid phase can undergo further hazardous waste treatment, while the liquid phase is transported to the disc stack separator by a screw pump. The centrifuge model used in this system is the GNLW553D-VFD.

Chemical Dosing Module:

To enhance the separation efficiency of the horizontal screw centrifuge, chemical dosing is typically used. Demulsifiers are used to break up more oil, while flocculants are used to separate more solid residues. The chemical dosing module includes demulsifiers, surfactants, and flocculants for oil sludge treatment.

The oil sludge treatment system designed by GN Solid Control is of great significance for waste treatment as it enables reduction in waste volume while recovering a significant amount of oil. It meets current environmental requirements by achieving energy savings, emission reduction, waste utilization, and efficient recovery.

If you have any requirements or inquiries about oil sludge treatment equipment and solutions, please contact GN Solid Control.

Last week, two units of the remarkable GNLW764A decanter centrifuge made their way to the project site. This centrifuge, an ingenious creation from GN Solids Control‘s research and development team, belongs to the esteemed 760mm series. With an impressive length-to-diameter ratio of 4.2:1, it stands as a testament to engineering excellence. Its generously-sized drum enables the processing of substantial volumes, making it an ideal solution for various applications such as shield tunneling slurry treatment and municipal wastewater management. In this particular endeavor, the centrifuge will play a crucial role in efficiently handling river dredging operations.

Complementing this advanced centrifuge are two units of the GNZS706F shale shaker, a masterpiece devised in-house. With a substantial screen area of 4.6㎡, this double-deck screen cleverly segregates particles based on their size. The upper deck addresses the removal of coarser particles, utilizing specialized smaller mesh sizes, while the lower deck further refines the separation process through the effective use of larger mesh sizes. This innovative vibrating screen delivers exceptional primary screening capabilities, effortlessly separating solid particles of 100 microns or more.

 

In addition, the project will benefit immensely from the significant contributions of two GNZS703F-2S Desilters and two GNZS703F-12N Desanders. These exceptional units feature wear-resistant polyurethane cones, ensuring longevity and durability. The desilters primarily function as reliable separators for solid particles above the size range of 40-60 microns. Meanwhile, the desanders ingeniously tackle particles ranging from 20-40 microns. Following the meticulous treatment provided by these impressive desilters and desanders, only fine particles ultimately reach the centrifuge, ensuring optimal performance and extending the equipment’s operational lifespan.

To facilitate efficient material transportation and maintain an environmentally conscious work site, twelve robust Screw Conveyors will be deployed. These conveyors, purpose-built for waste material transportation, aptly collect the solid phase separated by the exceptional vibrating screens, desilters, desanders, and centrifuges. They deftly carry the collected material to the designated locations, ensuring a clean and orderly project site. Equipped with removable sealing plates or steel grid plates, these conveyors prioritize the safety of operations. Additionally, they can be customized to include pull-wire switches, delayed start functions, and emergency stop buttons on the control box, further enhancing their functionality and usability.

Committed to delivering comprehensive solutions, GN Solids Control is not just limited to offering exceptional solid-liquid separation equipment. As part of their extensive product range, they also offer advanced liquid supply equipment, including centrifugal sand pumps, submersible slurry pumps, screw pumps, and vacuum pumps.

For any requirements in this domain, GN Solids Control stands ready to provide top-notch equipment and expertise.

GN Solids Control, a leading manufacturer of solids control equipment, provides stacked vibrating screens for iron ore sorting and processing projects. With three factories in China and subsidiary companies in the United States and Russia, GN Solids Control offers solutions for industries such as mining, environmental protection, and municipal waste treatment. Same time GN can supply other separation equipment like Decanter Centrifuge and Shale Shaker.

The stacked vibrating screen, developed by GN Solids Control, utilizes the principle of dual-degree-of-freedom resonance and is designed to be driven by a single excitation source, achieving linear vibration throughout the entire machine. This equipment features unique vibration patterns, energy-saving operation, high screening efficiency, large processing capacity, advanced technology, simple structure, and stable and reliable performance, making it an advanced device in the field of ore material screening. The equipment is suitable for wet screening, grading, and dewatering operations in industries such as mineral processing and coal preparation, and can be customized with 2 to 5 layers based on site requirements.

The screen box of the vibrating screen is arranged in multiple layers. It utilizes two counter-rotating vibrating motors as the vibration source, causing the screen mesh inside the screen box to undergo overall linear vibration transmitted by the entire assembly. This vibration is then transmitted to the material on the screen, achieving the purpose of vibrating screening.

The vibrating motor adopts advanced imported vibration motor technology (such as Martin or OLI motors), ensuring reliable operation with long trouble-free running time. Compared to similar screens, the stacked vibrating screen has advantages such as a small footprint, high processing capacity per unit area, high screening efficiency, low power consumption, low dynamic load, simple operation, stable performance, durability, and low maintenance requirements. The surface of the vibrating screen undergoes sandblasting treatment and is coated with heavy-duty anti-corrosion paint, providing excellent corrosion resistance. The surface in contact with the material is protected by a sprayed polyurethane wear-resistant and anti-corrosion layer, extending the life of the screen.

 

The supplied stacked vibrating screens are specifically used for iron ore sorting and processing.

If you have any equipment needs for the mining industry, including vibrating screens, please feel free to contact GN Solids Control.

With the improvement of environmental protection, most petroleum companies also require further treatment of mud to obtain clean oil, water and solid wastes, thereby improving the protection of the environment.

Recently, GN Solids Control provides US environmental protection companies with a 1 m3/h processing of mud processing system, providing the 15 m3/h sludge processing system for the Qatar service company, and providing a 5 m3/h oil mud treatment system for the Kuwait drilling service company.

 

In the oil -containing sludge treatment scheme provided by GN Solids Control for foreign customers, the main equipment is the snail centrifugal machine and spiral conveyor.

Decanter centrifuge

The GN decanter centrifuge is mainly used to separate solid particles with more than 2-5um. GN SOLIDS Control has a decanter centrifugal design with different bowl diameter, including 14-inch, 18-inch, 22-inch, and 30 inches. machine.

Screw conveyor

Screw conveyors are widely used in the transportation of solid -phase waste in drilling waste. The screw conveyors that provide customers this time are mainly used to transport solid -phase waste separated from centrifuge. The spiral blades of the GN Solids Control spiral conveyor are used for wear -resistant materials, which improves the service life of the product. The upper cover is protected by removable seals or steel grid plates to improve the safety of use.

GN Solids Control not only provides core devices, but also has better set processing system design and production capabilities, such as mud circulation system, mud without landing solutions. If you have this need, welcome contact GN Solids Control.