Author: admin

GN Solids Control recently produced 6 sets of vacuum adsorption vibrating screen units for offshore platform projects. The customer ordered the vacuum shaker screen unit from our company for the second time. The vacuum adsorption vibrating screen unit produced by GN Solids Control was in the first time. After use, it gives the customer a very satisfactory result. This is also the desire of GN Solids Control technicians to develop new products, which can satisfy every customer.

After more than a year of field simulation experiments, GN Solids Control plans to independently develop vacuum shale shaker equipment in combination with the advantages and performance of various products at home and abroad. The company applied for domestic and foreign patents for the first time, and vacuum adsorption by GN Solids Control. The device is used on the offshore platform by installing a vacuum adsorption device under the last screen of the vibrating screen. When used in the field, a certain frequency of vacuum absorption is formed by the pulsating airflow, which can effectively improve the recovery of the drilling fluid and reduce the discharge of cuttings. The liquid content. When the offshore platform is used in the field, the customer can already use the slag outlet of the vibrating screen to install a small screen with vacuum adsorption through the external type to realize the vacuum adsorption drilling fluid recovery before the cuttings are discharged.

GN Solids Control’s vacuum adsorption vibrating screen unit is used in a wide range of applications, including oil-based mud (BOM), water-based mud (WBM), and slurry-based mud (SBM).as a good solution for mud separate system It can also be applied to land drilling rigs and offshore drilling rigs, improving the efficiency of vibrating screens for solid-control equipment, recovering drilling fluids, reducing the amount of waste, and vacuum-adsorbing vibrating screen devices to replace the processing of drill cutting screens, but at a lower cost, with almost no additional land occupation. The area meets the space requirements of the offshore platform.

The vacuum adsorption vibrating screen device has become a new product of GN Solids Control and has been widely concerned by customers at home and abroad. Welcome customers to consult.

More question,welcome contact GN solids control

The drilling waste disposal screw conveyor is ready to be sent to the African site. The former African customers have ordered the chip dumping machine and the cuttings centrifuge in our company. At present, the screw conveyor has been tested and completed, ready to be packaged for shipment and delivery. The screw conveyors ordered by African customers are specially supplied to the on-site drilling platform for conveying waste cuttings management.

The screw conveyor produced by GN Solids Control is mainly used for waste treatment and drilling cutting of drilling fluid. The screw conveyor is the auxiliary equipment for the drilling mud solid phase separation and drying system equipment. The screw conveyor produced by GN Solids Control can be combined with other The transportation equipment is used together, and the screw conveyor completes joint transportation, separate transportation, mixing, blending, dehydration, compounding, unloading and stacking. GN Solids Control technicians use a custom designed screw conveyor as part of the waste processing system. The screw conveyor is designed to be 12 feet per section. This design of the GN Solids Control enables the screw conveyor to act as a screw conveyor. The replacement of standard consumable parts greatly reduces the convenience of customers on site. The spiral blades of spiral conveyors produced by GN Solids Control are made of wear-resistant materials to ensure their longevity is longer than the same type of products in the same industry.

GN screw conveyor can work with Decanter centrifuge and shale shaker

The screw conveyor produced by GN Solids Control is the main unit of transportation work in most industries, which can reduce the labor intensity, improve work efficiency and wide application range. Applicable to all industries, such as mud does not fall into the cuttings, building materials, chemicals, electricity, metallurgy, coal, grain and other industries, suitable for horizontal or inclined transport of powder, granular and small block materials, such as coal, ash, slag, Cement, grain, etc., a wide range of products, our company welcomes customers to inquire.

More question,welcome contact GN solids control

The three 600GPM non-excavation mud recovery systems ordered by Asian customers have been prepared after strict production, assembly and test procedures. The 600GPM non-excavation mud recovery system is compact and easy to transport. Customers design GN Solids Control. The concept and productivity are very satisfactory. In the field of non-excavation mud recovery system generation, GN Solids Control can design product solutions according to the actual situation and needs of customers, reduce costs and improve efficiency. Our customers are very satisfied with this.

The three sets of 600GPM non-excavation mud recovery systems ordered by Asian customers are the same. The main products are vibrating screen, desilter, 40-foot standard mud tank, mixing funnel and sand pump and other auxiliary equipment. 600GPM non-excavation All equipment and electrical components on the mud recovery system are equipped with international famous brands such as Siemens, Schneider, ABB, etc. The mud-removing cyclone is made of high-wear composite polyurethane material, all equipment paints are selected from marine anti-corrosion paint, and all accessories are internationally renowned. Brand names are interchangeable. The 600GPM non-excavation mud recovery system fully meets the needs of the local market for tropical climate environment construction. On-site Asian customers can maximize the use value of each equipment during use, and achieve the best mud purification and recovery effect.

GN Solids Control has a great reputation and praise in the production of HDD non-excavation mud recovery system. After years of product design and practical experience in the field, GN Solids Control has finally made customers choose to cooperate with GN Solids Control. New and old customers come to visit the GN Solids Control factory to discuss cooperation.

More question,welcome contact GN solids control

GN Solids Control has established good relationships with customers in Asia all the year round. The mud mixers and mud transfer pumps ordered by customers in this Asia are urgently needed on site. GN Solids Control’s employees are intensified according to the actual needs of Asian customers. It is required to successfully complete the processing test machine of the agitator and the mud transfer pump with the guarantee of quality and quantity during the delivery period. During this period, Asian customer supervision visited the site to check the production process and work progress. After the customer saw it, the professionalism of GN Solids Control products was praised and the professionalism of GN Solids Control employees was praised.

The agitator ordered by Asian customers adopts worm-worm reduction gear transmission. The shaft section is a circular-arc cylindrical worm. The turbine tooth shape is a circle conjugated with the turbine. It has the advantages of large transmission torque, stable operation and reliable operation. The agitator produced has a compact structure, a small floor space, a good stirring effect, a large stirring intensity, a wide spread range, and a reduced starting resistance distance.

The mud pump delivered by Asian customers mainly includes Centrifugal pump, vacuum pump and screw pump. The sand pump is designed for pumping drilling fluid or industrial suspension. Compared with ordinary pumps, it has excellent performance, large equipment flow, high temperature resistance on site, long service life, easy maintenance on site operators, high reliability and remarkable energy saving effect. Features. The vacuum pump transports more than 80% of the solid phase and high specific gravity materials at high speed. It is widely used in the transportation of waste mud from offshore platforms. The drill cuttings from the vibrating screen, the bottom of the sludge, the bilge cleaning of the ship, the sand, the fine sand. , and fracturing sand and other fields. Screw pump accessories are few, compatible structure, small size, easy maintenance, rotor and stator are the wearing parts of the pump, easy to replace. The screw pump stator is made of synthetic rubber and has special advantages over other pumps in transferring waste slurry of high viscosity and hard suspension.

GN Solids Control Products 60 to 80 per cent of exports in the international market, have been sold to more than 70 countries and regions, customers are welcome to come to counseling. More question,welcome contact GN solids control

Nine Shale shaker produced by GN Solids Control are sent to Shandong. The nine vibration-free motor vibrating screens produced by GN Solids Control will be used for primary screening of solid drilling control systems in Shandong customers. The previous GN Solids Control has been We have had many cooperations with customers in Shandong. The customers are very satisfied with the processing effect of the ordered vibrating screen. Therefore, we have chosen to cooperate with GN Solids Control again.

The vibrating screens produced by GN Solids Control can provide different processing capabilities and customized vibrating screens according to the needs of our customers. Vibrating screens are the first-level solid-phase control equipment for oil drilling mud solid-control systems. Usually GN Solids Control can be customized according to the size of the customer’s drilling rig. Different production of single vibrating screen, double vibrating screen or triple vibrating screen. At the same time, the vibrating screen produced by GN Solids Control can also be used as the bottom vibrating screen of the desander and desilter, or as the underflow vibrating screen of the sand removing and decontaminating machine. The vibrating screen electric screen box angle adjustment produced by our company, as well as the mechanical angle adjustment for standby, the screen box sealing patent design, the sealing effect is good, the bottom frame of the screen box is made of stainless steel, the corrosion resistance and the service life are greatly improved, the vibrating screen is electronically controlled. The electrical components of the cabinet use Siemens or Schneider components.

The vibrating screen is mainly composed of a base, a screen box, a screen, a logging tank, an excitation motor, a shock absorbing spring, a control switch, and an adjusting device. Judging from the use of various types of vibrating screens used in current oilfield production, the most widely used linear drilling fluid vibrating screen has the advantages of high sediment discharge speed, horizontal installation of sand surface and large processing capacity.

GN Solids Control is a professional manufacturer of mud vibrating shaker screens. The mud vibrating screens are widely used in oil drilling and HDD non-excavation industries. Welcome customers to consult.

More question,welcome contact GN solids control

Decanter centrifuge is one of GN’s main products that widely used in all kinds of drilling mud recycling and waste management. This week, GN just finished the fabrication of the variable speed decanter centrifuge ordered by an India drilling contractor.

Almost all the drilling contractors request the equipment used on oilfield to be explosion proof certified for safety consideration. To meet the customers’ requirement on explosion proof standard, GN is now able to provide equipment with motors and control panel certified by China national explosion proof CNEX, IEC Ex and ATEX.

The ordered decanter centrifuge is GN’s model GNLW363C-VFD. The bowl diameter is 14 inch (360mm), bowl length and diameter ratio is around 3, which explains the model of the centrifuge. GN’s 14 inch decanter centrifuge can be used for various purposes due to the VFD design. The typical working speed of this model is 3200RPM, at this speed, the fine solids with size down to 2-5 microns could be separated out without adding additional chemicals. By reducing the speed to around 2000RPM, this unit can be used for barite recovery in solids control system.

The bowl material of this unit is duplex stainless steel 2304 which is much better than SS316L. The centrifugal casting technic makes the bow material has a better distribution feature for better balance.

This unit is equipped with temperature sensor at both bearing seats to inspect the temperature of the bearing. And a vibration sensor is installed on the base for abnormal vibration. All the sensors are used to collect information of centrifuge running and send signal to the VFD control panel. By uploading program into the VFD panel, the panel could monitor the centrifuge and trip off the unit for protection.

The VFD control panel matched to the centrifuge has 3 VFDs for main and back motors of the centrifuge and the feeding pump. Operators could set the running parameters on the HMI screen to adjusting the centrifuge running condition. GN’s VFD panel is positive pressurized explosion proof method, together with the air conditioner, the VFD panel could be used in hazardous are with very high ambient temperature.

Both the decanter centrifuge and control panel are made by GN self. For more information on GN’s decanter centrifuge and other mud recycling equipment, please feel free to contact with GN.

More question,welcome contact GN solids control

GN solids control specializes in the development and manufacture of drilling mud solids control systems and drilling waste treatment equipment. GN solids control is the leading brand of solid control equipment at home and abroad. We have established branches in the US and Russia.

The water-based mud drilling fluid waste-processing system designed and developed by GN solids control is described as follows:

First, the system consists of:

1. Material collection and transmission system

2, cuttings dry processing system

3. Waste mud and wastewater solid-liquid mixture modulation system

4, centrifugal separation and dehydration system

5. Drilling treatment system

6, electronic control system

Water-based drilling fluid waste while drilling treatment system

Water-based drilling fluid waste while drilling treatment system

Second, the system industry characteristics

1, cuttings collection + cuttings dry + curing treatment system

The use of cuttings collection tank, screw conveyor, drill chip dryer, and cutting chip solidification system is beneficial to the treatment of different solid control systems under the condition of a drilling drill to discharge waste cuttings and carrying mud or running pulp. The harmless treatment of the drill cuttings with mud is also conducive to the rapid drying and semi-automation of cuttings treatment. It is easy to realize the safe disposal of cuttings and realize the clean production of drilling.

2, waste mud modulation + centrifugal separation dehydration system

The waste slurry generated by cementing and clearing can be broken and stabilized by a high-efficiency composite type breaker. It realizes fast and efficient solid-liquid separation of waste mud, saves floor space, and can fully realize the rapid gel breaking and stabilization treatment of waste mud.

The mud centrifuge processing module will be separated and dehydrated by adding waste mud such as gel breaking and flocculation. The initial rapid separation of the mud water is achieved, and the effluent is relatively clarified and the mud cake is formed.

3. Drilling sewage air flotation + precision filtration system

The sewage separated by the centrifuge is subjected to flocculation oxidative decolorization and emulsified oil demulsification separation treatment through a first-stage high-efficiency shallow air flotation device. Realize the flocculation separation, oxidative decolorization and petroleum-based removal treatment of small and medium organic matter in drilling wastewater. Then use high-fiber ball filter for high-precision filtration treatment to achieve wastewater reuse or efflux standard treatment.

More question,welcome contact GN solids control

Introduction of GN sohttp://gnsolidscontrol.com/lids control armored mud recovery system

First, the mud recovery system

The GN solids control armored mud recovery system is a mud circulation system that is designed and manufactured by GN Company according to the user’s requirements and according to the customer’s specific requirements for the treated mud. The system utilizes the flocculation dosing system to improve the processing capacity of the centrifuge. The system is powered by the GNG30A-075/GNG30A-075D screw pump. The user can select different dosing positions and dosing types of the flocculation system to make the mud have Different flocculation effects, so that the mud centrifuge achieves the desired satisfactory treatment effect, and the treated particulate matter is excluded from the system by the screw conveyor.

Mud recovery system

Second, the basic performance of the mud recovery system

1. The system has two warehouses: one is the mixing chamber, and the other is the storage chamber after the mud treatment; the whole system can remove most of the solid particles above 2μm after being processed by the centrifuge.

2. The mixing tank is equipped with a heating rod, and the customer can also replace the heating rods of different models and powers according to the needs of use.

3, design mud processing capacity: 5 m3 / h, rated mud processing capacity: 5m3 / h, adapt to the environment: -15 ° ~ 50 °.

4. Adapt to mud viscosity: ≤45 S.

5. Adapt to climatic conditions: rain, snow, fog weather.

6. It can work continuously under rated power.

7. Working height range: It can work normally at altitude ≤ 2500 m, and it can work effectively when the altitude is ≥ 2500 m.

8. All equipments of the system are mature technology new products, and the technical performance meets the relevant requirements of SY/T5612-2007 “Design Specification for Petroleum Drilling Fluid Solid Phase Control Equipment”.

9. The whole machine has reasonable design, compact structure, flexible combination, advanced technology, convenient operation and maintenance, and safe and reliable performance.

10. The system is easy to dispatch, transfer and transport, and can meet the domestic and foreign road transport regulations.

More question,welcome contact GN solids control

GN vertical dehumidifier uses centrifugal force to drain oil-based or synthetic-based drill cuttings. Stainless steel nets separate the “wet” solids and accelerate them to 900rpm. with G power of 420 G or super high speed of 1200 rpm. / min with a G force of 750 G. Liquid is passed through a hole in the grid, while “dry” solids are extracted using an angled flight attached to a cone that rotate somewhat slower than a rotor. The scraper is protected by a coating with carbide tungsten of abrasive solids and provides a long service life. This helps in keeping a constant gap between the scraper and the mesh, which is crucial for proper operation.

For waste management,normally client will use centrifuge together with vertical cutting dryer

Worker Show on GN Vertical Dryer Oil Based Waste Recycling Before Recycling After Recycling, OIL Content: 2.9% water based. So he meets the customer’s requirement to use one system for recycling with a lonely good result, without changing the treatment method for various drilling waste.

More question,welcome contact GN solids control

In the past, CIPPE 2018 in March of this year, GN Solid Management, showed an installation to install an oil sludge set to 1 set. This unit has all the necessary functional device for extracting oil from the oil sludge; it can be used in a small-scale oil sludge purification system or as a demonstration device for the user to check if the GN solution can solve the problem of oil sludge disposal. Many visitors to the GN booth have shown their interest in trying this equipment. One of the visitors contacted GN several days after the show and placed an order for this system. This sludge treatment unit consists of a pre-mix procedure, two-phase separation and three-phase separation. The main technologies used are flushing flushing for demulsifying and separating oil for different phases, such as oil, water and solids. The goal is to recover as much oil as possible and to get as little waste as possible.

Customer feedback suggests that the treatment of waste sludge, installed at GN, provides an effective solution for treating waste oil sludge in a well at the place of its installation. They are considering the possibility of starting further cooperation with GN by placing an order for a GN-type sludge treatment system with a large processing capacity.

The pre-mix procedure applies a pre-mix tank with a heat system, as well as a chemical dosing system. Oil sludge must be with a certain liquidity for easy transportation and mixing with chemicals.

The GN Mini Shale shaker GNZS752 and the 9-inch GNLW224 decantation centrifuge are basic equipment used in two-phase separation mode, this is the main GN product that has been approved with good performance and quality. sludge.

The images here show oil, water and solids discharged from the three-phase separation process. In this step, a disk centrifuge is used to receive the liquid discharged from the decantation centrifuge. When operating at high speeds, a disk centrifuge can effectively recover the oil from the slurry. GN can provide a larger capacity sludge treatment system to help the customer recover the oil and get more benefits. For more information, please feel free to contact GN