Month: April 2010

Oil Well Torch Introduction

The oil well torch is a electric ignition device, the oil well troch is used for igniting gas in oil and gas drilling. It is always used

company with the mud gas separator.GN Solids Control Flare Ignition Device is a good oil well torch and sells well all over the world.
The oil and well torch is a kind of handling arrangement used in blown down natural gas, the tail gas from collecting and distributing station of natural gas and from refinery.

The oil well torch can be used to ignited the harmful gas be fired which is used to be blown down. It is friendly to the enviorement. Continue reading “Oil Well Torch”

Our customers are always asking questions like: Can I have your reference list? Are your products adapt to our situation?  and so on… I konw what they really want to know: Why I choose GN Solids Control, and is there others used your products and do they satisfied with it?

Here we go!

Firstly, I will introduce you the principle of GN Solids Control: Only Top Quality Products! This is our promise!

Secondly, GN Solids Control supply all the parts of solids control system, including shale shakers, desanders, desilters, mud tank separation, centrifugal pumps, decanting centrifuges and so on, and GN supply all the products right as you required.

Shale shaker,linear motion shaker

Drilling mud shale shaker manufacturer,linear motion shale shakers for drilling fluids,Solids control shale shaker,oilfield drilling cuttings linear motion …

Derrick Replacement 503 PMD shaker screen to Brazil

Twin drilling mud shale shaker and backup spare parts to Morocco

desander,hydrocyclone desander,China desander desilter manufacturer

Hydrocyclone desander manufacturer,oilfield desander with good cones,buy solids control drilling mud fluids desander from China supplier for sale.

desilter-hydrocyclone fluids desilter,drilling mud desilter

Hydrocyclone desilter manufacturer,drilling fluids desilter,mud desilter and desander with good cones,China oilfield solids control desilter supplier.

mud tank,drilling fluids tank,mud tanks design

Drilling Mud tank manufacturer,drilling fluids tanks customized design,design mud tanks for Oil Gas drilling and HDD Solids Control mud system.

Storage mud tank agitator to Thailand

Premix mud tank equipments and spare parts to Kazakstan

Drilling mud tank recycle systems equipments for Kazakhstan

Our customer is all over the world, as you can see, and click here to know more about GN news…

Centrifugal pumps are also called sand pumps, used widely in oil and gas drilling, to pump the drilling fluids to keep the mud recycling system or solids control equipments work well.

The Definition of Centrifugal Pumps

Machine for moving fluid by spinning it using a rotating impeller in a casing with a central inlet and a tangential outlet.

Centrifugal pump design

The overwhelming majority of contractor pumps use centrifugal force to move water. Centrifugal force is defined as the action that causes something, in this case drilling fluids, to move away from its center of rotation.

Continue reading “General Information of Centrifugal Pump”

Drilling mud (drilling fluids) is used to Remove cuttings from well; Suspend and release cuttings; Control formation pressures; Seal permeable formations; Maintain wellbore stability; Minimizing formation damage; Cool, lubricate; and support the bit and drilling assembly; Transmit hydraulic energy to tools and bit; Ensure adequate formation evaluation; Control corrosion (in acceptable level); Facilitate cementing and completion.drilling fluids(drilling mud) is pumped from the surface through the hollow drill string, exits through nozzles in the drill bit, and returns to the surface through the annular space between the drill string and the walls of the hole.

The drill bit grinds rocks into drill cuttings, which are entrained in the mud flow and are carried out to the surface. And we separated the mud from the solids to make the mud return to the recirculating mud system. Continue reading “Oil Mud Separation”

M-I SWACO has been awarded a substantial multi services contract inclusive of drilling and completion fluids, drilling waste management, filtration, wellbore clean up tools, vessel cleaning and related services .
This contract is six year (with option for two additional years) and begins June 2010. The revenues is expected to result in approximately $800 million over the life of the agreement.
This contract routinely services 6 to 10 drilling rigs offshore Cabinda, Angola in Blocks 0 (shallow water) and Block 14 (deepwater).

Continue reading “M-I SWACO’s Service to Offshore Angola”

How to use a vibrator of shale shaker, it contains two keys: disassembly of the bibrator of shale shaker, reassembly of shale shaker. And you need exactly remmber that disconnect power to the electric motor and lock the disconnect swithch in the open position.

Disassembly of the Vibrator of Shale Shaker
WARNING: Disconnect power to the electric motor and lock the disconnect swithch in the open position.

1. Remove motor and drive pulley guard.
2. Remove the counterweight guard from both ends of the vibrator shaft.
3. Loosen the four motor support bolts located under the motor, loosen the V-belts and remove them.
4. Remove the V-belt sheave , by first loosening its taper lock hub.
5. Remove the counterweights , by removing the clamp screws and reusing the screw to open the slots in the counterweights, by tightening the screws into the tapped holes.
6. Remove the collars  and the retainers  with the Spiro lox rings  in their grooves. Remove cartridge cap screws.
7. Remove retaining ring  from the drive side only. By striking on one end of the shaft  with a lead hammer or a hammer and a block of hardwood, it is possible to start to drive out the cartridge  on the other side.
8. Then it should be easy to pry either or both cartridges loose from their bores in the housing ends. If difficulty is experienced a cartridge can be bumped from the inside by striking the shaft again at the other end. When one cartridge is removed the shaft can be slipped from the housing. Continue reading “How to Use a Vibrator of Shale Shaker”

Today,we received a client inquiry for Fluids System Inc. shale shaker screen panel.
GN solids control adopted particular screen production techniques and material of SS304 or SS316, we can produce shaker screens of replacement for world famous brand, and design and manufacture various sizes screens according to

the customer’s requirements.

Fludis System shaker screen specifications

Recently we produce some shaker screens for replacement of Fluid Systems Series 500 and 5000 shakers. Dimension:42”x29”, Material: SS304, Frame material: Iron.

Fluids System shaker screen Processing technology
MFX Series screens are general duty screen panels. This series of screens utilize tensile bolting cloth and are available in mesh sizes from 6 to 400. As with all Fluid Systems, Inc. O.E.M. screen panels, each screen is factory tensioned to eliminate improper tension in the field.
FMS series screens utilize the same cloth as MF screens with the addition of a perforated support plate and are available in mesh sizes from 10 to 400.The support plate offers extra support for heavy loading and reparability of damaged or worn sections of the screen panel. As with all Fluid Systems,Inc. O.E.M. screen panels, each screen is factory tensioned to eliminate improper tensioning in the field.
Continue reading “Fluids System Inc. shale shaker screen panel”

Desander and desilter hydrociclones are device to separate particles from drilling fluid, which is sorted by shale shaker in the first phase of solids control system. You can see in the first picture.

Usage of hydrocyclone

A hydrocyclone is often used to separate drilling cuttings from drilling mud originating at a desander desilter or some other continuous source of pressurized liquid. A hydrocyclone is most likely to be th

e right choice for processes where “lights” (drilling fluids, e.g.) are the greater part of the mixture and where the “heavies” (drilling cuttings e.g.) settle fairly easily.

Continue reading “Introduction of hydrocyclones in desander and desilter”

Derrick Equipment Company has agent in China,They brought Derrick DP600(Dual pool 600) shale shaker on 10th CIPPE.

The Derrick DP 600 (Dual Pool 600 shale shaker)incorporates numerous patent pending technological advancements designed to meet and exceed the evolving needs of the drilling industry. Innovative dual concave screen frame, increased fluid-handling capacity, a newly designed screen compression system and an optional scalping deck combine to provide a new standard in screening equipment. Continue reading “Derrick DP600(Dual pool 600) shale shaker on CIPPE”