GN-SEPARATION-TEST-SITE-CARRIED-OUT-INTO-PRACTICE

GN Separation test site mainly consists of 5 module.

  1. Mining vibrating screen test module
  2. Drilling shale shaker test module
  3. Decanter centrifuge test module
  4. Shale shaker and centrifuge integrated separation test module
  5. Solid vacuum pump test module

Based on these 5 separation module, GN can provide a complete test report with the tested sample materail from the client that definitely will do make sense to select the equipment type and model in an efficient and objective way.

For helping you with more about GN, please follow the brief introduction below.

Overview

GN Solids Control is a Chinese company that specializes in the design, manufacturing, and service support of solids control equipment and waste management systems primarily for the oil & gas drilling, HDD (Horizontal Directional Drilling), CBM (Coal Bed Methane), and environmental industries.

Key Products and Equipment

GN manufactures the entire suite of solids control equipment, often sold as individual units or integrated into a complete system called a “mud recycling system” or “shale shaker system.”

  1. Shale Shakers: The primary and first stage of solids control. They use vibrating screens to separate large drilled cuttings from the drilling fluid. GN offers linear motion and elliptical motion shakers.

  2. Vacuum Degassers: Remove entrained gases (like methane or H₂S) from the drilling fluid, which is critical for safety and maintaining mud density.

  3. Desanders & Desilters: Hydrocyclones that use centrifugal force to remove fine sand and silt-sized particles (the second and third stages of cleaning).

  4. Decanter Centrifuges: High-speed centrifuges that separate extremely fine particles and colloidal solids. They are crucial for barite recovery (saving expensive weighting material) and dewatering.

  5. Centrifugal Pumps: Provide the necessary pressure to move drilling fluid through the entire cleaning system.

  6. Mud Cleaners: A combination unit that typically integrates a desander/desilter with a shaker screen.

  7. Complete Systems: GN designs and builds customized, skidded systems that combine all the above components for a specific drilling project’s needs. This includes:

    • Mud Recycling System (for O&G Rigs)

    • Slurry Separation System (for HDD, Piling, Tunneling)

    • Cuttings Dewatering System

    • Waste Management Unit

    • Strengths and Reputation

Complete Product Line: Offers a one-stop-shop for all solids control needs.

Cost-Effectiveness: Known for providing reliable equipment at a more competitive price point than traditional Western manufacturers, offering excellent value.

International Focus: Has a strong export department and a global network of agents and distributors. They provide multi-language support and their documentation is often available in English, Russian, Spanish, etc.

Customization: Ability to design and build systems to meet specific client requirements and space constraints on drilling rigs.

Service and Support: Provides training, installation supervision, and after-sales spare parts support globally.

Summary
GN Solids Control Co., Ltd. is a leading Chinese manufacturer that has successfully captured a significant share of the global solids control market by providing a full range of reliable, cost-effective equipment for drilling fluid processing and waste management.

To have more detail about site cases, please contact MichaelSong for a prompt reply.

Whatsapp: + 86 178 0179 9913

Email: michael@gnseparation.com

 

FREQUENCY-CONVERSION-CENTRIFUGE-SOLD-TO-CUSTOMERS-IN-THE-MIDDLE-EAST

GN Solids Control is a leading manufacturer of decanter centrifuges for drilling fluid solids control, waste management, and industrial separation. These centrifuges are critical for fine solids removal, barite recovery, and sludge dewatering in oil & gas, HDD, and environmental applications.

Key Features of GN Decanter Centrifuges

  1. High-Speed Separation G-force up to 3,200×g for efficient solids-liquid separation.

Adjustable RPM (1,500–4,200) to optimize performance for different slurries.

  1. Robust & Wear-Resistant Design Tungsten carbide or ceramic tiles on critical wear parts (scroll, conveyor).

Stainless steel (SS304/316) or duplex steel construction for corrosion resistance.

  1. Precise Control & Automation Variable frequency drive (VFD) for adjustable bowl & conveyor speed.

PLC control system (optional) for real-time monitoring of torque, differential speed, and flow rate.

  1. Versatile Applications Drilling fluid recovery (removes 2–7μm particles).

Barite & bentonite recycling (reduces mud costs).

Sludge dewatering (oil sludge, industrial waste).

Applications Oil & Gas Drilling – Fine solids removal, barite recovery.

HDD & Tunneling – Bentonite slurry recycling.

Environmental – Oil sludge treatment, wastewater dewatering.

Mining & Industrial – Tailings processing, chemical separation.

Why Choose GN Solids Control?

✅ 20+ Years of Centrifuge Expertise – Reliable performance in harsh conditions.

✅ Custom Solutions – Different sizes (10″–24″ bowl), materials, and automation levels.

✅ Global Support – Installation, training, and spare parts available worldwide.

For any prompt reply and detai info, please find Michaelsong.

Position: Marketing Manager

Whatsapp: + 86 178 0179 9913

Email: michael@gnsolidscontrol.com/michael@gnseparation.com

Micro Centrifuges And Drilling Mud Purification Equipment Sold To Europe

GN Solids Control Co., Ltd. is a Chinese company specializing in the design, manufacturing, and service of solid control systems and related equipment for the oil and gas drilling industry.

Core Products & Services
Solids Control Equipment

Shale shakers

Desanders & desilters

Decanter centrifuges

Mud cleaners

Vacuum degassers

Decanter Centrifuge by GN Solids Control GN Solids Control is a leading manufacturer of decanter centrifuges for drilling fluid solids control, waste management, and industrial separation. These centrifuges are critical for fine solids removal, barite recovery, and sludge dewatering in oil & gas, HDD, and environmental applications.

Key Features of GN Decanter Centrifuges

  1. High-Speed Separation G-force up to 3,200×g for efficient solids-liquid separation.

Adjustable RPM (1,500–4,200) to optimize performance for different slurries.

  1. Robust & Wear-Resistant Design Tungsten carbide or ceramic tiles on critical wear parts (scroll, conveyor).

Stainless steel (SS304/316) or duplex steel construction for corrosion resistance.

  1. Precise Control & Automation Variable frequency drive (VFD) for adjustable bowl & conveyor speed.

PLC control system (optional) for real-time monitoring of torque, differential speed, and flow rate.

  1. Versatile Applications Drilling fluid recovery (removes 2–7μm particles).

Barite & bentonite recycling (reduces mud costs).

Sludge dewatering (oil sludge, industrial waste).

Key Features
High Efficiency: Advanced separation technology for drilling fluid recovery.

Environmental Compliance: Helps reduce waste and meet HSE standards.

Global Certifications: ISO 9001, API, CE, and other industry standards.

Applications
Onshore & offshore oil drilling

HDD (Horizontal Directional Drilling)

Tunneling & mining

Why Choose GN Solids Control?
Strong R&D capabilities

Customized solutions for different drilling conditions

After-sales support & maintenance services

For case info in detail, please find Michael Song

Whatsapp: + 86 178 0179 9913

Email: michael@gnseparation.com

4-SETS-OF-WORKOVER-RIG-SOLIDS-CONTROL-EQUIPMENT-SOLD-TO-INDONESIAN-CUSTOMERS

GN Solids Control Co., Ltd. is a Chinese company specializing in the design, manufacturing, and service of solid control systems and related equipment for the oil and gas drilling industry.

Core Products & Services

  1. Solids Control Equipment

    • Shale shakers

    • Desanders & desilters

    • Decanter centrifuges

    • Mud cleaners

    • Vacuum degassers

2 .Drilling Waste Management

Cuttings dryers

Slurry separation systems

Thermal desorption units (for oil recovery from cuttings)

3. Mud Recycling Systems

Closed-loop systems for drilling fluid recovery

4. Customized Solutions

Containerized and skid-mounted systems for offshore/onshore drilling

A shale shaker is the first and most critical solids control equipment in drilling operations. It removes large drilled cuttings (≥75μm) from drilling fluid using vibrating screens, allowing clean mud to be reused.

Benefits of GN Shale Shakers
✔ Superior Solids Removal – Extends the life of downstream equipment (desanders, centrifuges).
✔ Low Maintenance – Easy screen replacement & durable construction.
✔ Energy Efficient – Optimized vibration motors reduce power consumption.
✔ Compatible with All Mud Types – Water-based, oil-based, synthetic-based.
✔ Global Certifications – API RP 13C, ISO 9001, CE, ATEX (for explosive environments).

A mud cleaner is a 2-stage or 3-stage solids control device that removes medium to fine particles (15-75μm) from drilling fluid after the shale shaker. It typically consists of:

Shale shaker (for coarse solids removal)

Hydrocyclones (desander + desilter for finer separation)

Bottom sieve (optional, for ultra-fine recovery)

GN Solids Control supplies high-efficiency mixing hoppers (also called mud hoppers or jet hoppers) for fast and uniform preparation of drilling fluids. These are essential for blending bentonite, polymers, additives, and weighting materials into water or oil-based mud systems.

For the prompt reply and cases, find MichaelSong.

Europe/Aisa Marketing Manager

Whatsapp: + 86 178 0179 9913

HDD-MUD-MIXING-TANK-AND-MUD-CLEANING-UNIT-FOR-MIDDLE-EAST-CUSTOMER

GN Solids Control provides specialized mud recycling systems for trenchless drilling (HDD, microtunneling, pipe jacking) to maximize fluid reuse, reduce costs, and minimize environmental impact.

Why Use a Mud Recycling System in Trenchless Drilling? Recovers expensive drilling fluids (bentonite, polymers).

Reduces disposal costs of waste slurry.

Maintains optimal mud properties for lubrication and bore stability.

Prevents jobsite pollution (compliance with EPA, local regulations).

Key Components of GN’s Trenchless Mud Recycling System

1.Shale Shaker (Primary Solids Removal) GNZS Linear Motion Shaker

Removes coarse cuttings (≥75μm).

Adjustable screen mesh for different soil types.

2.Desander & Desilter (Secondary Cleaning) Hydrocyclones (10-50μm separation) for finer solids.

3.Mud Mixing & Storage System Jet mixing hopper for fresh mud preparation.

Agitation tanks to maintain slurry consistency.

4.Cuttings Handling (Optional) Screw conveyor – Transports separated solids to disposal.

Vertical cuttings dryer (VCD) – Further reduces fluid on waste (for <5% moisture).

System Workflow
Used slurry returns from the borehole.

Shale shaker removes large cuttings.

Desander/desilter takes out medium-fine particles.

Clean mud is pumped back into the system.

Solids are discharged for disposal.

Benefits of GN’s Trenchless Mud Recycling System
✔ Saves 30-50% on drilling fluid costs by recycling bentonite/polymers.
✔ Compact & mobile – Skid-mounted or trailer-based for easy transport.
✔ Improves drilling efficiency – Clean mud = better borehole stability.
✔ Reduces environmental liability – Complies with EPA, IADC, and ISO 14001.
✔ Fully automated control – PLC system for easy operation.

Applications
Horizontal Directional Drilling (HDD)

Microtunneling & Pipe Jacking

Utility Installation (Fiber, Gas, Water Lines)

Geothermal Loop Drilling

GN’s Customizable Solutions
Small HDD Rigs → Compact units (e.g., GNMS-50, 50m³/h capacity).

Large Tunneling Projects → High-volume systems (up to 200m³/h).

Zero-Discharge Systems – Closed-loop recycling for urban areas.

Why Choose GN Solids Control?
✅ 15+ Years in Trenchless Mud Recycling
✅ Global Support (USA, Europe, Asia)
✅ API & CE-Certified Equipment

For cases,Michael Song will be there ready for you.

Whatsapp:+ 86 178 0179 9913

Email: michael@gnosolidscontrol.com

TRENCHLESS-SLURRY-HANDLING-SYSTEM-SOLD-TO-MIDDLE-EAST-CUSTOMERS

GN Solids Control Co., Ltd. is a Chinese company specializing in the design, manufacturing, and service of solid control systems and related equipment for the oil and gas drilling industry.

GN Solids Control provides specialized mud recycling systems for trenchless drilling (HDD, microtunneling, pipe jacking) to maximize fluid reuse, reduce costs, and minimize environmental impact.

Why Use a Mud Recycling System in Trenchless Drilling?
Recovers expensive drilling fluids (bentonite, polymers).

Reduces disposal costs of waste slurry.

Maintains optimal mud properties for lubrication and bore stability.

Prevents jobsite pollution (compliance with EPA, local regulations).

Key Components of GN’s Trenchless Mud Recycling System

  1. Shale Shaker (Primary Solids Removal) GNZS Linear Motion Shaker

Removes coarse cuttings (≥75μm).

Adjustable screen mesh for different soil types.

  1. Desander & Desilter (Secondary Cleaning) Hydrocyclones (10-50μm separation) for finer solids.

GNZJ Series – Compact design for HDD rigs.

  1. Decanter Centrifuge (Ultra-Fine Separation) GNLW Series – Recovers bentonite & removes colloidal solids (down to 2-5μm).

Variable Speed Control – Adjusts for different slurry densities.

  1. Mud Mixing & Storage System Jet mixing hopper for fresh mud preparation.

Agitation tanks to maintain slurry consistency.

  1. Cuttings Handling (Optional) Screw conveyor – Transports separated solids to disposal.

Vertical cuttings dryer (VCD) – Further reduces fluid on waste (for <5% moisture).

System Workflow
Used slurry returns from the borehole.

Shale shaker removes large cuttings.

Desander/desilter takes out medium-fine particles.

Centrifuge polishes mud for reuse.

Clean mud is pumped back into the system.

Solids are discharged for disposal.

Applications
Horizontal Directional Drilling (HDD)

Microtunneling & Pipe Jacking

Utility Installation (Fiber, Gas, Water Lines)

Geothermal Loop Drilling

Why Choose GN Solids Control?
✅ 15+ Years in Trenchless Mud Recycling
✅ Global Support (USA, Europe, Middle East, Asia)
✅ API & CE-Certified Equipment

Any cases request, find Michaelsong contact.

Whatsapp: + 86 178 0179 9913(prompt reply)

2-SETS-OF-GNOST-15-OILY-SLUDGE-TREATMENT-SYSTEMS-SOLD-TO-ASIAN-CUSTOMERS

GN Solids Control Co., Ltd. is a Chinese company specializing in the design, manufacturing, and service of solid control systems and related equipment for the oil and gas drilling industry.

Oil sludge is a hazardous byproduct of drilling, tank cleaning, and refinery operations, containing oil, water, and solid particles. GN Solids Control provides advanced oil sludge treatment systems to recover oil, reduce waste, and meet environmental regulations.

GN Oil Sludge Treatment Process GN’s system typically includes mechanical separation, thermal treatment, and chemical conditioning for maximum oil recovery.

  1. Pretreatment (Sludge Screening & Heating) Screw Pump/Grit Separator → Removes large debris.

Heating System (optional) → Lowers viscosity for better separation.

  1. Primary Separation (3-Phase Decanter Centrifuge) GNLW Series Centrifuge separates:

Recovered Oil (reusable)

Water (can be treated further)

Solids (≤5% residual oil, safe for disposal)

  1. Secondary Treatment (Thermal Desorption or Chemical Washing) Thermal Desorption Unit (TDU) → For heavy sludge, removes oil via heating (optional).

Chemical Demulsifiers → Enhances oil-water separation.

Key Equipment in GN’s Oil Sludge Treatment System
Equipment Function
Sludge Transfer Pump Moves sludge into the system
Heating Mixer Reduces viscosity
3-Phase Centrifuge Separates oil, water, solids
Thermal Desorption Unit Deep cleaning for solids
Screw Conveyor Discharges dried solids
Oil/Water Storage Tanks Collects recovered fluids

Applications
Oilfield Drilling Waste (OBM cuttings, pit cleaning)

Tank Bottom Sludge Treatment

Refinery Waste Processing

Oil Spill Cleanup (soil remediation)

Why Choose GN Solids Control?
10+ Years of Experience in sludge treatment.

Customizable Solutions (small mobile units to large plants).

Global Support (Africa, Middle East, Americas, Asia).

Would you like technical specifications or a case study?

Find MichaelSong contact below.

Whatsapp: + 86 178 0179 9913

Email: michael@gnsolidscontrol.com/michael@gnsolidscontrol.co

GN-SHALE-SHAKER-AND-MUD-CLEANER-FOR-OFFSHORE-DRILLING-PLATFORM

GN Solids Control Co., Ltd. is a Chinese company specializing in the design, manufacturing, and service of solid control systems and equipment for the oil and gas drilling industry.

Key Products & Services:
Solids Control Equipment

Shale Shakers

Desanders & Desilters

Decanter Centrifuges

Mud Cleaners

Vacuum Degassers

Drilling Waste Management

Cuttings Dryers

Slurry Separation Systems

Thermal Desorption Units

Customized Systems

Modular Solids Control Systems

Offshore & Onshore Drilling Solutions

After-Sales Support

Spare Parts Supply

Technical Maintenance

Field Service

Applications:
Oil & Gas Drilling

HDD (Horizontal Directional Drilling)

Tunneling & Mining

Environmental Waste Treatment

Global Presence:
GN serves clients worldwide, with exports to regions like the Middle East, North America, Africa, and Southeast Asia. The company holds certifications such as API, ISO9001, and CE, ensuring compliance with international standards.

The inserted second pic tells “shale shaker”,

A shale shaker is a critical piece of solids control equipment used in drilling operations to remove large drill cuttings (rock fragments) from drilling fluid (mud). It is the first and most important stage in the solids separation process, ensuring efficient drilling performance and fluid reuse.

The inserted first pic tells “mud cleaner”,

A mud cleaner is a crucial solids control device used in drilling operations to remove fine drill cuttings (+25 microns) and low-gravity solids (LGS) from drilling fluid (mud). It combines hydrocyclones (desanders & desilters) and a fine-mesh shaker screen to enhance solids removal efficiency.

For more info and prompt reply, please find MichaelSong.

Whatsapp:+ 86 178 0179 9913

Email: michael@gnsolidscontrol.com

DRILING-MUD-RECYCLING-UNIT-AND-DECANTER-CENTRIFUGES-FOR-OVERSEAS-CLIENT

GN Solids Control Co., Ltd. is a Chinese company specializing in the design, manufacturing, and service of solid control systems and equipment for the oil and gas drilling industry.GN provides solutions for drilling fluid purification, waste management, and solids separation.

Key Products & Services:
Solids Control Equipment

Shale Shakers

Desanders & Desilters

Decanter Centrifuges

Mud Cleaners

Vacuum Degassers

Drilling Waste Management

Cuttings Dryers

Slurry Separation Systems

Thermal Desorption Units

Customized Systems

Modular Solids Control Systems

Offshore & Onshore Drilling Solutions

After-Sales Support

Spare Parts Supply

Technical Maintenance

Field Service

Applications:
Oil & Gas Drilling

HDD (Horizontal Directional Drilling)

Tunneling & Mining

Environmental Waste Treatment

Global Presence:
GN serves clients worldwide, with exports to regions like the Middle East, North America, Africa, and Southeast Asia. The company holds certifications such as API, ISO9001, and CE, ensuring compliance with international standards.

For any prompt reply,please find MichaelSong

Whatsapp: + 86 178 0179 9913

Email: michael@gnsolidscontrol.co

ONE-BATCH-OF-SOLIDS-VACUUM-PUMP-FOR-AFRICA-OILFIELD-SERVICE-COMPANY

GN Solids Control Co., Ltd. is a Chinese company specializing in the design, manufacturing, and service of solid control systems and related equipment for the oil and gas drilling industry. Here are some key details about the company.

Core Products & Services
Solids Control Equipment

Shale shakers

Desanders & desilters

Decanter centrifuges

Mud cleaners

Vacuum degassers

Drilling Waste Management

Cuttings dryers

Slurry separation systems

Thermal desorption units (for oil recovery from cuttings)

Mud Recycling Systems

Closed-loop systems for drilling fluid recovery

Customized Solutions

Containerized and skid-mounted systems for offshore/onshore drilling

Key Features
High Efficiency: Advanced separation technology for drilling fluid recovery.

Environmental Compliance: Helps reduce waste and meet HSE standards.

Global Certifications: ISO 9001, API, CE, and other industry standards.

Applications
Onshore & offshore oil drilling

HDD (Horizontal Directional Drilling)

Tunneling & mining

Why Choose GN Solids Control?
Strong R&D capabilities

Customized solutions for different drilling conditions

After-sales support & maintenance services

For any prompt reply and more info in detail, please find MichaelSong.

Whatsapp: + 86 178 0179 9913

Email: michael@gnsolidscontrol.co