General requirements for all mud tanks.

shale shaker tank

Three-runner oilfield type, 7’-10’’ wide with a 6’’ loading hich on each and for tailboarding. skid extenions decked with ¼’’ plate. tank walls rimmed with 7’’ square tubing full length of tanks.tanks side and end walls constructed of ¼’’ crimped plate for rigidity.

Detail requirements for the shale shaker tank.

520 bbls four (4) compartment shaker tank, 10’ widex 8’ deep x 37’’ long mounted on a 40’ long skid per above general spesifications and including.
tank compartments as follows:
91 bbls sand trap compartment
143 bbls degasser compartment
143 bbls desander compartment
143 bbls desilter compartment
three (3) full partition with equalizer valves

grating around shale shaker include tubing handrails and toe boards.
removable walkway with handrails to suction tank and trip tank.
one (1) 12’’ ditch connection to suction tank.
one (1) 6’’ mud gunning line connection to intermediate tank.
one (1) 2’’ water line connection to suction tank
one (1) psi 10 hp agitator supplied and mounted in desilter compartment.
one (1) stair to ground with handrails.
one (1) 1’’ diameter x 25’ long valved water washdown hose.
one (1) water connection to desilter trough.
one (1) water connection to desander trough.
16’’ x 18’’ mud ditch 10’’ dump gate to each compartment.
two (2) shaker slides
two (2)GN patent  shale shakers supplied and installed
one (1) psi 1000 degasser supplied and installed.
one (1) psi 10-cone desilter supplied and instaled.
one (1) psi 2-cone desander supplied and installed.
one (1) 3’’ bottom mud gun with butterfly valve in each compartment.
three (3) 10’’ butterfly valve clean-out gate – one (1) each in desander, degas and desilt compartment.
one (1) 12’’ butterfly valve clean-out gate in sand trap compartment.
two (2) 8×6 centrifugal pumps with mechanical seals and 75 hp, 1800 rpm, 480 volt, 3-phase, 60 hz xp ac motors sup and mounted on the side of the tank.
one (1) 12’’ bottom equalizer to suction tank.

Oilfield shale shaker tank (1) is a post from: Mud Solids Control Equipment

No related posts.

Related posts brought to you by Yet Another Related Posts Plugin.

ZJ drilling rig are the models of Chinese made drilling rig,GN Solids Control Mud circulation system for ZJ Drilling rig as below:

• ZJ Deep well drilling rig mud system:
  

  ZJ drilling rig mud system

·  ZJ90/6750DB DRILLING RIG
·  ZJ120/9000DB DRILLING RIG

• ZJ70 drilling mud solids control equipments:

·  ZJ70/4500DB TRACK MODULAR RIG
·  ZJ70/4500LD Drilling Rigs
·  ZJ70/4500L Drilling Rigs
·  ZJ70/4500DS Desert Drilling Rigs
·  ZJ70/4500D Drilling Rigs

• ZJ50 drilling mud recycling system:

·  ZJ50/3150L Drilling Rigs
·  ZJ50/3150D E-Drive Drilling Rigs

• ZJ40 drilling mud solids control equipments:

·  ZJ40/2250T9 Drilling Rigs
·  ZJ40/2250LT Drilling Rigs
·  ZJ40/2250L1 Drilling Rigs
·  ZJ40/2250L Series Drilling Rigs
·  ZJ40/2250DB Drilling Rigs

• ZJ30 drilling mud circulation system:

·  ZJ30/1700JD Drilling Rigs
·  ZJ30/1700DZ Drilling Rigs
·  ZJ30/1700B Series Drilling Rigs
·  ZJ30/1700 Drilling Rigs

• ZJ20 drilling mud solids control system:

·  ZJ20/1350ZDB Drilling Rigs
·  ZJ20/1350Z Truck-Mounted Drilling Rigs

• Other drilling mud circulation system for drilling rig.

·  ZJ15X Slant Hole Drilling Rigs
·  ZJ15/900DB-1 Drilling Rigs
·  ZJ10/585 drilling rigs
·  1500m Drilling Rigs

To the specifications and design of ZJ series drilling mud circulation system,and the marched drilling mud equipments,please contact GN Solids Control sales team.Cost-effective mud equipments and system from GN Solids Control.

ZJ Drilling rig mud system|Equipments is a post from: Mud Solids Control Equipment

No related posts.

Related posts brought to you by Yet Another Related Posts Plugin.

PNEUMATIC SPINNING WRENCHES

This is really what we call trust!!

Q254-250 PNEUMATIC SPINNING WRENCHES

The wrench is the best replacement of rotary rope (or chain). It is applied for the mechanized spinning operation. The applicable range of pipe diameter is wide, and it can be freely adjusted whenever necessary. There are two configurations for clamping mechanism: air tyre and air cylinder. There are two driving and controlling styles: pneumatic and hydraulic. The spinning wrench is designed and manufactured according to API Spec 7K “Specification for Drilling Equipment

As a solids control equipments to manufacturer,we keep giving our clients reliable service.And now we even win the trust of our customer for PNEUMATIC SPINNING WRENCHES.

Supply PNEUMATIC SPINNING WRENCHES is a post from: Mud Solids Control Equipment

No related posts.

Related posts brought to you by Yet Another Related Posts Plugin.

LW355-1250N series of high speed centrifuge produced by our company can better meet the above requirements.
Model and technical parameters.

Horizontal decanter centrifuge

2.1 Centrifuge Model：GLW  355-1250N
High quality stainless steel made
Effective roller length 1250mm
Inner diameter of the roller 355mm

High speed horizontal decanter centrifuge
2.2 Technical parameters
Rated liquid processing capacity：40m3/h
Rated slag tipping capacity：5t/h
Mix separation point：2μm
Rotating speed：3200rpm
Highest separation factor：2035
Main frame power：37kw
Auxiliary frame power：7.5kw
Pump engine power: 5.5kw (standard deploying 5.5kw long-pole pump, can deploy 11kw screw pump according to the need)
Features of this GLW  355-1250N High speed horizontal decanter centrifuge
a)    Oil gas exploration developer wish to use more clean mud drilling to protect the oil gas layer so as to achieve higher oil gas production.
b)    The using of turbo screw drilling technology put forward higher requirements on the mud cleanness.
c)     More attention will be paid to the disused mud treatment, while treat the disused mud is mainly to separate solid phase from liquid phase as much as possible.

Medium speed centrifuge can separate solid phase granule with the diameter of 5~7μm in low-viscosity mud, as to the thinner granule and high-viscosity mud or the granule in oil based mud, it can not separate them well. So, medium speed centrifuge can hardly meet the new requirements of solid-control system, deploying high speed centrifuge is the development trend in future.
LW355-1250N series of Horizontal high speed centrifuge produced by our company can better meet the above requirements.

Horizontal Decanter Centrifuge Manufacturer-GN is a post from: Mud Solids Control Equipment

No related posts.

Related posts brought to you by Yet Another Related Posts Plugin.

Drilling fluids management system

GN Solids Control is 1 of about 10 China manufacturers who can design and manufacture all the equipments for a complete drilling fluids management system

All the drilling fluids management equipments are mounted over the drilling mud tank.

There are many ways to configure your mud tanks below your drilling fluids management equipment. The most common practice requires three sections. Under your shale shaker you have the first section known as the sand trap where the mud to be pumped from this section goes through your Desander. This cleaned mud is then dumped into the second section known as a silt tank. The mud is picked up then pumped through your Desilters. The Desilters dumps the cleaned mud into the third section, know as the clean mud or mixing tank. This will be picked up by  the pump to be pumped back into your bore hole.

To provivide Combination Desanders/Desilters are common when the volume being pumped is under 500 GPM. The tank separation in this drilling fluids managemet application can be achieved with two sections in the mud tank. A clean section where mud to be mixed and pumped down hole is located. The second section is under the shale shaker where the contaminated mud is picked up and processed by the Desander/Desilter combination.

The drilling fluids management Equipments

• Drilling fluids Shale Shakers

The first line of defense for a properly designed drilling fluids management system has been and will continue to be, the shale shaker. Without proper screening of the drilling fluid during this initial removal step, reduced efficiency and effectiveness of all downstream drilling fluids management in the system is assured. The downstream hydrocyclones will simply be overloaded beyond their designed capacity.

• Drilling fluids Hydrocyclones

Hydrocyclones are simple mechanical devices, with out moving parts, designed to speed up the settling process. Feed pressure is transformed into centrifugal force inside the cyclone or cone to accelerate particle settling in accordance with Stoke’s Law #1. In essence, a cyclone is a miniature settling pit which alloys very rapid settling of solids under controlled conditions.Hydrocyclones have become important in drilling fluids management system because of their ability to efficiently remove particles smaller than the finest mesh screens.

• Drilling fluids decanting centrifuge

Decanter centrifuge are used to process unweighted and weighted, water-based and oil-based drilling fluids (muds). Mechanical energy is utilized to increase the gravitational force exerted on solids that are present in the mud system.oilfield Decanting Centrifuge are able to apply over 3,000 G-forces on the liquid/solids mixture, which separates the heavier solids from the lighter solids.

Other drilling fluids management equipments includes:centrifugal pump,drilling fluids degasser,etc.

Contact GN Solids Control for complete drilling fluids management system solution.

Drilling fluids management system manufacturer is a post from: Mud Solids Control Equipment

No related posts.

Related posts brought to you by Yet Another Related Posts Plugin.

oilfield centrifugal pump

Get centrifugal pump tech specs here:Sand pump
Definition of centrifugal pump
Machine for moving fluid by spinning it using a rotating impeller in a casing with a central inlet and a tangential
outlet

Note of Centrifugal pump:

NOTE The path of the fluid is an increasing spiral from the inlet at the centre to the outlet, tangent to the impeller annulus.
In the annular space between the impeller vane tips and the casing wall, the fluid velocity is roughly the same as that of
the impeller vane tips. Useful work is produced by the pump when some of the spinning fluid flows out of the casing
tangential outlet into the pipe system. Power from the motor is used to accelerate the fluid entering the inlet up to the
speed of the fluid in the annulus. Some of the motor power is expended as friction of the fluid in the casing and impeller.

These centifugal pumps are developed and fabricated  as supporting pumps based on requirement of transferring oil & gas drilling fluid. Centrifugal pump adopt the axial sucking structure and all the hydraulic components are wear proof cast iron, which is suitable for delivering the corrosive liquids with suspended particles in well drilling. Its quality is accepted by Weatherford and assembling dimension is same to Mission centrifugal pump.

SB centrifugal pumps are characteristic of abrasion resistance, smooth and stable running, reliable sealing, long service life and convenient maintenance.  Those pumps have been used for land and offshore drilling platforms in more than 20 countries over the world.

Clockwise pumps and anti-clockwise pumps are available.

Mechanical seal and compound seal are available. The compound seal adopts auxiliary impeller, special oil seal and packing seal. Main seal of mechanical  seal is mechanical seal with a long service life, auxiliary seal of machine seal is packing seal to prevent occurrence of accidents.
Shaft seals are lubricated with grease and bearings are lubricated with machine oil and grease  Since bearing covers at two ends of bearings are equipped with grease injectors.

Both inlet flanges and outlet flanges for centrifugal pump are with two series standard dimensions.

Centrifugal pump are widely used in oilfield drilling equipments and drilling mud equipments like shale shakers,desanders desilters etc.Top China  Centrifugal Pump company for drilling mud,welcome to consult us for centrifugal pump for oilfield drilling projects.We supply centrifugal pump worldwide.

Oilfield Centrifugal Pump for drilling is a post from: Mud Solids Control Equipment

No related posts.

Related posts brought to you by Yet Another Related Posts Plugin.

Now the policy as below:

All the interested agents are requested to send their details by filling the Agent Application form below. If the agency business is not a registered business(as company) then we will need a letter of reference and bank details.

Download

Products Brochure

Application Form

How to become our agent?

• Download & Fill & Summit your Application Form for being our agent to Email: